Configure Cisco VSS

Source: Internet
Author: User
Tags session id switches cisco vss

Cisco VSS Configuration
One, the 2 VSS65 from the single-box mode switch to Virtual chassis mode
Basic steps:
1. Configure the SSO High Availability protocol on switches 1 and 2, respectively:
2. Configure the domain of the virtual switch (VM switch domain and switch Numbers)
3. Configure the VSL port between the two switches (connecting using the 2 Wan ports on the engine)
4. Convert chassis into Virtual Switch mode

Detailed configuration:
1. Configure the SSO High Availability protocol on switches 1 and 2, respectively:
SWITCH1:
Step 1
Switch-1 (config) # redundancy
Enters redundancy configuration mode.
Step 2
Switch-1 (config-red) # mode SSO
Configures SSO. When this command was entered, the redundant Supervisor engine is reloaded and begins to work in SSO mode.
Step 3
Switch-1 (config-red) # exit

switch-1# Show Running-config
switch-1# Show redundancy states//displays the operating redundancy mode.

SWITCH2:
Switch-2 (config) # redundancy
Switch-2 (config-red) # mode SSO
Switch-2 (config-red) # exit

switch-2# Show Running-config
switch-2# Show Redundancy states

2. Configure the domain of the virtual switch (VM switch domain and switch Numbers)
SWITCH1:
Step 1
Switch-1 (config) # switch virtual domain 100
Step 2
Switch-1 (config-vs-domain) # switch 1
Step 3
Switch-1 (Config-vs-domain) # exit

SWITCH2:
Switch-2 (config) # switch virtual domain 100
Switch-2 (config-vs-domain) # switch 2
Switch-2 (Config-vs-domain) # exit

3. Configure the VSL port between the two switches (connecting using the 2 Wan ports on the engine)
1) Configure Channel
SWITCH1:
Step 1
Switch-1 (config) # interface Port-channel 10
Step 2
Switch-1 (config-if) # switch Virtual link 1
Step 3
Switch-1 (config-if) # no shutdown//activates the port channel.
Step 4
Switch-1 (config-if) # exit

SWITCH2:
Switch-2 (config) # interface Port-channel 20
Switch-2 (config-if) # switch Virtual link 2
Switch-2 (config-if) # no shutdown
Switch-2 (config-if) # exit

2) Add the Gbps port on the engine to the channel (assuming that the engine is SLOT3, make sure Port-channel has joined switch virtual link)
SWITCH1:
Switch-1 (config) # interface range Tengigabitethernet 3/1-2
Switch-1 (config-if) # Channel-group mode on
Switch-1 (config-if) # no shutdown

SWITCH2:
Step 1
Switch-2 (config) # interface range Tengigabitethernet 3/1-2
Switch-2 (config-if) # Channel-group mode on
Switch-2 (config-if) # no shutdown

4. Convert chassis into Virtual Switch mode
1) Check the chassis PFC mode to ensure the same 2 chassis
Step 1
switch-1# Show platform hardware PFC mode
Ensures that the PFC operating mode matches on both chassis, to ensure that the VSS comes up in SSO redundancy mode.
Step 2
switch-2# Show platform hardware PFC mode
Step 3
Switch-1 (config) # Platform hardware VSL PFC mode pfc3c
(Optional) Sets the PFC operating mode to pfc3c on Chassis A.
Step 4
Switch-2 (config) # Platform hardware VSL PFC mode pfc3c
(Optional) Sets the PFC operating mode to pfc3c on Chassis B.

2) switch Chassis mode
SWITCH1:
switch-1# Switch Convert mode virtual
Converts switch 1 to virtual Switch mode.
After you enter the command, your is prompted to confirm the action. Enter Yes.
The system creates a converted configuration file, and saves the file to the RP Bootflash.

SWITCH2:
switch-2# Switch Convert mode virtual


5. View VSS Information
router# Show Switch virtual
Displays the virtual switch domain number, and the switch number and role for each of the chassis.

router# Show Switch Virtual role
Displays the role, switch number, and priority for each of the chassis in the VSS.

router# Show switch Virtual link
Displays the status of the VSL.

The following example shows the information output from these commands:
router# Show Switch virtual
Switch mode:virtual switch
Virtual Switch Domain number:100
Local Switch number:1
Local Switch Operational role:virtual switch Active
Peer Switch Number:2
Peer Switch Operational role:virtual switch Standby

router# Show Switch Virtual role
Switch switch Status Preempt priority Role Session ID
Number Oper (Conf) Oper (Conf) Local Remote
------------------------------------------------------------------
LOCAL 1 Up FALSE (N) ACTIVE 0 0
REMOTE 2 up FALSE (N) STANDBY 8158 1991

In dual-active recovery Mode:no

router# Show switch Virtual link
VSL Status:up
VSL uptime:4 hours, minutes
VSL SCP Ping:pass OK
VSL ICC (Ping): Pass
VSL Control Link:te 1/5/1


Welcome Lai Qun 1,666,846,201 Exchange

This article is from the "Network around us." Blog, so be sure to keep this source http://willy.blog.51cto.com/5093185/1618831

Configure Cisco VSS

Contact Us

The content source of this page is from Internet, which doesn't represent Alibaba Cloud's opinion; products and services mentioned on that page don't have any relationship with Alibaba Cloud. If the content of the page makes you feel confusing, please write us an email, we will handle the problem within 5 days after receiving your email.

If you find any instances of plagiarism from the community, please send an email to: info-contact@alibabacloud.com and provide relevant evidence. A staff member will contact you within 5 working days.

A Free Trial That Lets You Build Big!

Start building with 50+ products and up to 12 months usage for Elastic Compute Service

  • Sales Support

    1 on 1 presale consultation

  • After-Sales Support

    24/7 Technical Support 6 Free Tickets per Quarter Faster Response

  • Alibaba Cloud offers highly flexible support services tailored to meet your exact needs.