Dell r510_r410_r610_r710 and all server installation Win2003 Solutions _ server Other

If you need to load the array card driver with a U disk when installing Windows 2003, please refer to the following method:

Drivers that may need to be loaded after the installation is complete http://support1.ap.dell.com/cn/zh/forum/thread.asp?fid=15&tid=254001

Support 9g,10g,11g installation windows2003, and 2003 Best with SP2 patch, otherwise there may be a blue screen crash and other phenomena. 8G not tested for the time being.
After using the software, U disk data will be lost!
Using the software, u disk data format will not be used by Windows system, you need to reformat before normal use.
System installation after the U disk recovery method http://support1.ap.dell.com/cn/zh/forum/thread.asp?fid=15&tid=233665

Note: Software with USBKeyPrepA00 version, do not use A07 version.

1: If you use tool software in Vista system, you need to right-click USBKeyPrepF6.exe and choose to run as Administrator.

2: The process of making drive U disk, if prompted to fail, it is recommended to check whether there are other programs to use U disk, you can try to close all other programs, plug the U disk, and then open the tool production.

3: Confirm if there is a remote control card (DRAC). If so, disable virtual media. (Check to see if disabled, check F11 boot menu without virtual floppy or virtual CDROM)
(Disabled method: see the Ctrl+e during the self-test and press it into the menu. Select Virtual Media Configuration and then set virtual media to detached.)

4: In the BIOS, integrated device inside the floppy drive is set to OFF.

5: First plug in the U disk and then boot

6: The installation process is best to press F6 load, according to the prompts in the selection "s", need to press 3 times "s" and carriage return, to confirm the use of virtual floppy drive. (See the prompt "S=use the driver on floppy" and press "S" to confirm loading)

Special attention:
If you are prompted to insert a floppy disk immediately after pressing S, check 3, 4 considerations.
If the partition is formatted, copy the file when prompted to insert a floppy disk, try to reboot, reboot from the CD, do not Press "F6" to try to load automatically from the U disk. (Because the Windows installation CD has an SP problem.) For the changed Windows installation CD-ROM or the All-in-one CD-ROM, it is likely to press F6 and do not press F6 will still be prompted to insert the floppy disk, the solution is to change the original version of the disc without change.

Drive method to make U disk: (Note that the download tools and compression are in the local hard drive, do not put on a U disk to run) (if prompted to fail, direct point prepare button retry two times, generally can be successful)
Download the tool for the array card from the link below. Run directly.
1:perc-s100_s300_2k3
Click here to download the attachment
2:PERC-S100_S300_2K3 (X64)
Click here to download the attachment
3:perc-h200_2k3
Click here to download the attachment
4:perc-h200_2k3_x64
Click here to download the attachment
5:perc-h700_800_2k3
Click here to download the attachment
6:perc-h700_800_2k3_x64
Click here to download the attachment
7:perc5i/perc5e/perc6i/perc6e_2k3
Click here to download the attachment
8:PERC5I/PERC5E/PERC6I/PERC6E_2K3 (64bit)
Click here to download the attachment
9:perc4e_2k3
Click here to download the attachment
10:PERC4E_2K3 (64bit)
Click here to download the attachment
11:sas5i/sas5e/sas5ir/sas6ir_2k3
Click here to download the attachment
12:SAS5I/SAS5E/SAS5IR/SAS6IR_2K3 (64bit)
Click here to download the attachment
13:sas5i/sas5e/sas5ir/sas6ir_xp
Click here to download the attachment
14:SAS5I/SAS5E/SAS5IR/SAS6IR_XP (64bit)
Click here to download the attachment
15:ADAPTEC39320_2K3_XP_2K3 (64bit)
Click here to download the attachment
16:adaptec39320 (EMU) _2k3_2k3 (64bit)
Click here to download the attachment
17:sata 1.5-6ch_2k3
Click here to download the attachment
18:sata 1.5-6ch_2k3 (64bit)
Click here to download the attachment
19:perc 320DC_WK3
Click here to download the attachment
20:cerc 2s_2k3
Click here to download the attachment
21:cerc 2s_2k3 (x64)
Click here to download the attachment
Download the extract to the desired temp directory, then go to the uncompressed directory and run USBKeyPrepF6.exe.
Vista system using tool software, you need to right-click USBKeyPrepF6.exe, choose to run as an administrator.

At this point you re-plug the U disk and then double-click U Disk, will be prompted to insert a diskette drive, said U drive to do a good job.
If you can still open your USB drive to see the inside of the file, the description is not done well.

To start the Install server:

1, the U disk inserted in the server to be installed after the (recommended) USB port, restart the server, the system CD-ROM in the CD-ROM, press f11=boot menu, enter the boot menu, confirm the U disk has been recognized. The installation starts normally from the CD.

Select Boot from CD drive:

2, at the bottom of the screen, there is information: press F6 If you need to install a third the party SCSI or RAID driver, the "F6" key in time.

3, after the "F6" is pressed, the installer will continue to load the module. This is normal. After a while, you will see the following information: Setup could not determine the type of one or more mass storage devices installed in your system, or you ha ve chosen to manually specify a adaptor.

4, click "S", the name of the driver in the U disk appears

5, hit return confirmation, the information in the red box driver is loaded. Return to the installation.
See the following figure, and press the S key confirmation, before the real load.

6, identify the hard drive:

7, move the cursor to an unassigned partition to create a partition by C: (Default to all capacity, need to manually change the recommendation C disk 20G)

8, move the cursor to the C-disk location Select Return to install, choose NTFS Quick format:

If you are prompted to insert a floppy disk again when you copy the file, follow the instructions at the beginning of the document to try.