Flisikar imx51 configuration parameters and startup information

---------------------------------
Bbg u-boot> PRI
Bootdelay = 1
Baudrate = 115200
Loadaddr = 0x90800000
Netdev = eth0
Ethprime = fec0
Uboot_addr = 0xa0000000
Uboot = u-boot.bin
Kernel = uimage
Rd_loadaddr = 0x90b00000
Nfsroot =/opt/ELDK/ARM
Bootargs_base = setenv bootargs console = ttymxc0, 115200
Bootargs_nfs = setenv bootargs $ {bootargs} root =/dev/nfs IP = DHCP nfsroot =$ {serverip }:: {nfsroot}, V3, TCP
Boottransfer_net = run bootargs_base bootargs_nfs; tftpboot $ {loadaddr }$ {kernel}; bootm
Prg_uboot = tftpboot $ {loadaddr }$ {uboot}; protect off $ {uboot_addr} 0xa003ffff; erase $ {uboot_addr} 0xa003ffff; CP. B
$ {Loadaddr }$ {uboot_addr }$ {filesize}; setenv filesize; saveenv
Bootcmd = run bootcmd_sd
Boottransfer_sd = run bootargs_base bootargs_android; MMC read 0 $ {loadaddr} 0x800 1800; MMC read 0 $ {rd_loadaddr} 0x2000 0x258; bootm
$ {Loadaddr }$ {rd_loadaddr}
Bootargs_android = setenv bootargs $ {bootargs} androidboot. Console = ttymxc0 init =/init dimo-primary Calibration
Bootcmd_android_recovery = run bootargs_base bootargs_android_recovery; MMC read 0 $ {loadaddr} 0x800 0x1800; bootm
Bootargs_android_recovery = setenv bootargs $ {bootargs} init =/init root =/dev/mmcblk0p4 rootfs = ext4 di1_primary

Stdin = serial
Stdout = serial
Stderr = serial
Ethact = fec0
------------------------------------------------------
Dmesg:
U-boot 2009.08-00145-g574c6ff (11 minutes later 09 2010-20:12:29)

CPU: Freescale I. MX51 family 3.0 V at 800 MHz
MX51 pll1: 800 MHz
MX51 pll2: 665 MHz
MX51 pll3: 216 MHz
IPG clock: 66500000Hz
IPG per clock: 665000000Hz
UART clock: 66500000Hz
CSPI clock: 54000000Hz
Board: MX51 Babbage 3.0 [por]
Boot device: MMC
I2C: Ready
DRAM: 512 MB
MMC: fsl_esdhc: 0, fsl_esdhc: 1
In: Serial
Out: Serial
Err: Serial
PMIC mode: SPI
Press home + power to enter recovery mode...
Net: fec0 [prime]
Hit any key to stop autoboot: 0

MMC read: Dev #0, block #2048, Count 6144...
6144 blocks read: OK

MMC read: Dev #0, block #8192, count 600...
600 blocks read: OK
# Booting kernel from legacy image at 90800000...
Image name: Android Linux Kernel
Image Type: ARM Linux kernel image (uncompressed)
Data size: 2246592 bytes = 2.1 MB
Load address: 90008000
Entry Point: 90008000
Verifying checksum... OK
# Loading init ramdisk from legacy image at 90b00000...
Image name: yy Android root filessystem
Image Type: ARM Linux ramdisk image (uncompressed)
Data size: 213047 bytes = 208.1 KB
Load address: 90308000
Entry Point: 90308000
Verifying checksum... OK
Loading kernel image... OK
OK

Starting kernel...

Uncompressing
Linux ....................................... ........................................ .........................................
........................................ ...... Done, booting the kernel.
Linux version 2.6.31-00839-g28694f3 (root @ tom-desktop) (GCC version 4.1.2) #3 preempt wed Dec 15 13:10:16 CST 2010
CPU: armv7 processor [412fc085] Revision 5 (armv7), Cr = 10c53c7f
CPU: vipt nonaliasing data cache, vipt nonaliasing Instruction Cache
MACHINE: Freescale MX51 Babbage Board
Memory Policy: ECC disabled, data cache writeback
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 109728
Kernel command line: Console = ttymxc0, 115200 init =/init androidboot. Console = ttymxc0 di1_primary calibration IP = DHCP
Unknown boot option 'androidboot. Console = ttymxc0 ': ignoring
PID hash table entries: 2048 (Order: 11,819 2 bytes)
Dentry cache hash table entries: 65536 (Order: 6, 262144 bytes)
Inode-Cache hash table entries: 32768 (Order: 5, 131072 bytes)
Memory: 432 MB = 432 MB total
Memory: 432236kb available (4700 K code, 875 K data, 136 K init, 0 K highmem)
Slub: genslabs = 11, hwalign = 32, order = 0-3, minobjects = 0, CPUs = 1, nodes = 1
Nr_irqs: 368
Mxc IRQ initialized
Mxc_early serial console at mmio 0x73fbc000 (options '123 ')
Console [ttymxc0] Enabled
Console: Color dummy device 80x30
Calibrating delay loop... 799.53 bogomips (lpj = 3997696)
Mount-Cache hash table entries: 512
CPU: Testing write buffer coherency: OK
Regulator: core version 0.5
Net: Registered protocol family 16
I. mx Iram pool: 128 kb @ 0xdb840000
Iram ready
CPU is I. MX51 re vision 3.0
Mxc gpio hardware
Iomux_config_mux: Warning: iomux pin config changed, Reg = f7ea8134, Prev = 0x1 new = 0x3
Using sdma I. API
Mxc dma api initialized
Bio: Create slab <bio-0> at 0
SCSI subsystem initialized
CSPI: mxc_spi-0 probed
Mxc I2C driver
Mxc I2C driver
Mxc HS I2C driver
Ipu dmfc Normal Mode: 1 (0 ~ 1), 5B (4, 5), 5f (6, 7)
Mc13892 rev 2.0 finver 2 Detected
Initializing regulators for Babbage.
Regulator: SW1: 600 <--> 1375 mv
Regulator: sw2: 900 <--> 1850 mv
Regulator: sw3: 1100 <--> 1850 mv
Regulator: sw4: 1100 <--> 1850 mv
Regulator: swbst: 0 mV
Regulator: viohi: 0 mV
Regulator: vpll: 1050 <--> 1800 mv
Regulator: vdig: 1650 mv
Regulator: ASD: 1800 <--> 3150 mv
Regulator: vusb2: 2400 <--> 2775 mv
Regulator: vvideo: 2775 mv
Regulator: vaudio: 2300 <--> 3000 mv
Regulator: VCAM: 2500 <--> 3000 MV Fast Normal
Regulator: vgen1: 1200 mv
Regulator: vgen2: 1200 <--> 3150 mv
Regulator: vgen3: 1800 <--> 2900 mv
Regulator: vusb: 0 mV
Regulator: gpo1: 0 mV
Regulator: gpo2: 0 mV
Regulator: gpo3: 0 mV
Regulator: gpo4: 0 mV
Device spi1.0 probed
Net: Registered protocol family 2
IP Route cache hash table entries: 4096 (Order: 2, 16384 bytes)
TCP established hash table entries: 16384 (Order: 5, 131072 bytes)
TCP bind hash table entries: 16384 (Order: 4, 65536 bytes)
TCP: Hash Tables configured (established 16384 bind 16384)
TCP Reno registered
Net: Registered protocol family 1
Trying to unpack rootfs image as initramfs...
Freeing initrd memory: 208 K
Lpmode driver module loaded
Static power management for Freescale I. MX51
PM driver module loaded
SDRAM autogating driver module loaded
Bus freq driver module loaded
Di1 is primary
Mxc_dvfs_core_probe
Dvfs driver module loaded
I. mxc CPU frequency driver
Dvfs per driver module loaded
Ashmem: initialized
Ms gmni has been set to 844
ALG: no test for stdrng (krng)
Io scheduler Noop registered
Io scheduler anticipatory registered
Io scheduler deadline registered
Io scheduler CFQ registered (default)
Mxc_ipu: channel already disabled 9
Mxc_ipu: channel already uninitialized 9
Console: switching to color frame buffer device 100x30
Fbcvt: 1024x768 @ 60: CVT name-. 786m3
Regulator: Get () with no identifier
Regulator: Get () with no identifier
Regulator: Get () with no identifier
Mxci2c_wait_writefifo: Wait Error
Serial: mxc internal UART driver
Mxcintuart.0: ttymxc0 at mmio 0x73fbc000 (IRQ = 31) is a Freescale I. mx
Console handover: boot [ttymxc0]-> real [ttymxc0]
Mxcintuart.1: ttymxc1 at mmio 0x73fc0000 (IRQ = 32) is a Freescale I. mx
Mxcintuart.2: ttymxc2 at mmio 0x7000c000 (IRQ = 33) is a Freescale I. mx
BRD: module loaded
Loop: module loaded
Pmem_adsp: 1 init
Pmem_gpu: 3 init
Mxc_dataflash spi1.1: jedec id 000000 not handled
Mice: cocould not register psaux device, error:-16
Mice: PS/2 mouse device common for all mice
Mxc keypad loaded
CLK: Unable to get requested clock: kpp_clk
Input: mxckpd as/devices/virtual/input/input0
Mc13892 RTC probe start
Pmic_rtc pmic_rtc.1: RTC core: Registered pmic_rtc as rtc0
Mc13892 RTC probe succeed
I2C/dev entries driver
Linux video capture interface: v2.00
I2c-adapter i2c-0: Bus busy
Ov3640_write_reg: Write Reg error: Reg = 3012, val = 80
Mxc_v4l2_output mxc_v4l2_output.0: Registered device video1
Mxc watchdog driver 2.0
CLK: Unable to get requested clock: wdog_clk
Mxc watchdog #0 Timer: initial timeout 60 sec
Device-mapper: uevent: Version 1.0.3
Device-mapper: IOCTL: 4.15.0-IOCTL () initialised: dm-devel@redhat.com
VPU initialized
Mxsdhci: mxc Secure Digital host controller interface driver
Mxsdhci: mxc sdhci controller driver.
Mmc0: sdhci detect IRQ 128 IRQ 1 Internal DMA
Mxsdhci: mxc sdhci controller driver.
Mmc1: sdhci detect IRQ 134 IRQ 2 internal DMA
Registered LED Device: pmic_ledsr
Registered LED Device: pmic_ledsg
Registered LED Device: pmic_ledsb
Logger: created 64 K log 'Log _ main'
Logger: created 256 k log 'Log _ events'
Logger: created 64 K log 'Log _ Radio'
Logger: created 64 K log 'Log _ System'
Advanced Linux sound architecture driver version 1.0.20.
Regulator: Unable to get requested regulator: vddd
Sgtl5000-i2c 1-000a: sgtl5000 revision 17
Mmc0: New High Speed sdhc card at address 0001
Mmcblk0: mmc0: 0001 appsd 3.90 Gib
Mmcblk0: P1 P2 P3 <P5 P6> p4
No device for Dai imx-ssi-1-0
No device for Dai imx-ssi-1-1
No device for Dai imx-ssi-2-0
No device for Dai imx-ssi-2-1
DMA sound buffers allocated: useiram = 1 Buf-> ADDR = 1fff6000 Buf-> area = db856000 size = 24576
DMA sound buffers allocated: useiram = 1 Buf-> ADDR = a9258000 Buf-> area = fa317000 size = 24576
ASOC: sgtl5000 imx-ssi-2-0 mapping OK
ALSA device list:
#0: imx-3stack (sgtl5000)
TCP cubic registered
Net: Registered protocol family 10
IPv6 over IPv4 tunneling driver
Net: Registered protocol family 17
RPC: Registered UDP Transport module.
RPC: Registered TCP transport module.
<6> DVI device plug-out
VFP support v0.3: implementor 41 architecture 3 part 30 Variant c rev 2
Regulator_init_complete: disabling gpo4
Regulator_init_complete: disabling gpo3
Regulator_init_complete: disabling gpo2
Regulator_init_complete: disabling gpo1
Regulator_init_complete: disabling vgen1
Regulator_init_complete: disabling VCAM
Regulator_init_complete: disabling vaudio
Regulator_init_complete: disabling
Regulator_init_complete: disabling swbst
Input: mxc_ts as/devices/virtual/input/input1
Mxc input touchscreen loaded
Pmic_rtc pmic_rtc.1: setting system clock to 1970-01-01 00:00:13 UTC (13)
IP-config: No network devices available.
Freeing init memory: 136 K
Init: cannot open'/initlogo. RLE'
Kjournald starting. Commit interval 5 seconds
EXT3-fs warning: maximal Mount count reached, running e2fsck is recommended
Ext3 FS on mmcblk0p2, internal journal
EXT3-fs: mounted filesystem with writeback data mode.
Kjournald starting. Commit interval 5 seconds
EXT3-fs warning: maximal Mount count reached, running e2fsck is recommended
Ext3 FS on mmcblk0p5, internal journal
EXT3-fs: Recovery complete.
EXT3-fs: mounted filesystem with writeback data mode.
Kjournald starting. Commit interval 5 seconds
EXT3-fs warning: maximal Mount count reached, running e2fsck is recommended
Ext3 FS on mmcblk0p6, internal journal
EXT3-fs: Recovery complete.
EXT3-fs: mounted filesystem with writeback data mode.
# Warning: 'rild' uses 32-bit capabilities (legacy support in use)
Init: cannot find '/system/etc/covery', disabling 'Flash _ recovery'
Pmem: Request for physical address of pmem region from process 1990.
Request_suspend_state: wakeup (3-> 0) at 39935103615 (00:00:50. 414590698 UTC)
Not all allocated memory blocks were freed. Doing it now.
Freeing List entry #0, gpuaddr = ab300000
Freeing List entry #1, gpuaddr = ab301000
Freeing List entry #2, gpuaddr = ab311000
Freeing List entry #3, gpuaddr = ab343000
Freeing List entry #6, gpuaddr = ab364000
Freeing List entry #7, gpuaddr = ab366000
Freeing List entry #8, gpuaddr = ab0000000
Freeing List entry #272, gpuaddr = ab786000