Soft routing Configuration Related commands

Routing Configuration basic commands

Access-enable allow routers to create temporary access list entries in the Dynamic access list
Access-group applying an Access control List (ACL) to an interface
Access-list defines a standard IP ACL
Access-template manually replace the temporary access list entry on the connected router
Appn sending commands to the APPN subsystem
Atmsig Executing ATM signaling commands
B Manual boot of the operating system
Bandwidth setting the bandwidth of the interface
Banner MOTD Specify date information banner
Bfe Setting the Burst event manual mode
The boot system specifies the system image that is loaded when the router starts
Calendar Set Hardware Calendars
Cd Change Path
CDP enable allows interface to run CDP protocol
Clear Reset function
Clear counters Clearing interface counters
Clear interface The piece logic on the interface reboot
Clockrate set the clock rate of the serial hardware connection, such as the rate at which the network interface module and interface processor can be accepted
CMT turn on/off FDDI connection management function
Config-register Modifying configuration Register settings
Configure allows access to the existing configuration mode, maintaining and saving configuration information on the central site
Configure Memory load configuration information from NVRAM
Configure Terminal manual configuration from the terminal
Connect to open a terminal connection
Copy replication configuration or image data
Copy Flash TFTP backup system image file to TFTP server
Copy Running-config Startup-config Stores the current configuration in RAM to the NVRAM
Copy Running-config TFTP stores the current configuration in RAM on a network TFTP server
Copy tftp Flash downloads a new image from the TFTP server to flash
Copy tftp running-config Download the configuration file from the TFTP server
Debug using Debugging Features
Debug Dialer shows what number the interface is dialing and the information
Debug IP Rip shows RIP route selection update data
Debug IPX Routing activity displays information about routing protocol (RIP) update packets
Debug IPX SAP Displays information about SAP (Business Announcement Protocol) Update packet
Debug ISDN q921 shows the access process for the data Link layer (layer 2nd) that occurs on the router D-Channel ISDN interface
Debug PPP Displays the business and exchange of information that occurs in implementing PPP
Delete deleting files
Deny sets a condition for a named IP ACL
Dialer idle-timeout Specifies the length of idle time before the line is disconnected
Dialer map set up a serial interface to call one or more locations
Dialer Wait-for-carrier-time rules How long it takes to wait for a carrier
Dialer-group access control by configuring interfaces that belong to a specific dialing group
Dialer-list protocol defines a digital data receiver (DDR) dial-up table to control dial control by a combination of protocols or ACLs and protocols
Dir displays files on a given device
Disable Closing Concession Mode
Disconnect disconnecting an established connection
Enable Open Concession Mode
Enable password to determine a password to prevent unauthorized access to the router
Enable Password set local password to control access at different privilege levels
Enable secret defines an additional layer of security for the Enable Password command (enforced security, password non-plaintext display)
Encapsulation Frame-relay boot Frame Relay encapsulation
Encapsulation Novell-ether specifies Novell's unique format for use on network segments
Encapsulation PPP to set PPP as the encapsulation method used by the serial or ISDN interface
Encapsulation SAP rules the Ethernet 802.2 format used on the network segment Cisco's password is SAP
END Exit Configuration mode
Erase deleting flash or configuring cache
Erase startup-config Delete content from NVRAM
Exec-timeout Configure the time that the EXEC command interpreter waits before it detects user input
Exit exit all configuration modes or close an active terminal session and terminate an exec
Exit terminates any configuration mode or closes an active dialog and ends exec
Format formatted device
Frame-relay Local-dlci to start the local management interface (LMI) for serial lines that use Frame Relay encapsulation
Help for interactive assistance systems
History View historical record
Hostname uses a hostname to configure the router, which is used as a prompt or as a default file name
Interface setting the interface type and input interface configuration mode
Interface configuring interface types and entering interface configuration modes
Interface Serial Select interface and input interface configuration mode
Ip Access-group Control access to an interface
IP Address set the network logical addresses of the interfaces
IP address sets an interface and subnet mask and begins IP processing
Ip Default-network establishing a default route
Ip Domain-lookup allows routers to use DNS by default
IP host defines static hostname to IP address mapping
Ip name-server Specifies a maximum of 6 server addresses for name-address resolution
Ip Route establishes a static route
IP unnumbered in the case of assigning an explicit IP address to an interface, the Internet Protocol (IP) process is initiated on the serial port
IPX Delay Set Point count
IPX Ipxwan start the Ipxwan protocol on the serial port
IPX Maximum-paths Sets the number of equivalent paths used by Cisco IOS software when forwarding packets
IPX network initiates routing of Internet Packet Switching (IPX) on a specific interface and chooses the type of encapsulation (encapsulated in frame)
Routing protocol used by IPX router
IPX Routing start IPX routing selection
IPX Sap-interval Set less frequent SAP (business AD Protocol) updates on slower links
IPX type-20-input-checks restrictions on the acceptance of propagation of IPX20 class packet broadcasts
ISDN SPID1 A Business briefing Number (SPID) that has been assigned to the B1 channel by the ISDN service provider on the router
ISDN SPID2 A Business briefing Number (SPID) that has been assigned to the B2 channel by the ISDN service provider on the router
Isdntch-type the type of switch that specifies the central office area on the ISDN interface
Keeplive for Serial Line LMI (local management interface) mechanism using Frame Relay encapsulation
Lat Open lat Connection
Line to determine a specific route and start line configuration
Line Concole set console port lines
Line Vty provides a virtual terminal for remote console access
Lock locks the terminal console
Login initiates a password check during terminal session logon
Login log in as a user, allow password verification at logon
Logout Exit EXEC Mode
Mbranch down-tracking multicast address routed to Terminal
Media-type Defining media types
Metric Holddown Isolate the new IGRP routing information from the in-use IGRP routing information for a period of time
Mrbranch up the multicast address routing to the branch end
Mrinfo getting neighbor and version information from the multicast router
Mstat display Statistics after multiple route tracking for multicast addresses
Mtrace Yuyuan The multicast address path to the target trace
Name-connection naming an existing network connection
Ncia turn on/off Ncia server
Network assigns a NIC-based address to a router directly connected to it to connect the network to an IGRP routing process. In IPX router configuration mode, the enhanced IGRP is started on the network
Network Specifies a segment that is directly connected to the router
Network-number a direct connection to the network
No shutdown open a closed interface
Pad opens a x.29 pad connection
Permit setting conditions for a named IP ACL
Ping sends the ICMP response request packet to another node on the network to check the accessibility of the host and network connectivity to diagnose the basic connectivity of the network
Ping sends echo requests to diagnose basic network connectivity
PPP begins IETF point-to-dot protocol
PPP authentication initiates the Challenge Handshake Authentication Protocol (CHAP) or Password Authentication Protocol (PAP) or both, and specifies the sequence of CHAP and PAP validations selected on the interface
PPP chap hostname When you authenticate with CHAP, create a batch of dial-up routers that appear to be the same host
PPP chap Password sets a password that is sent to the host command that authenticates the router to limit the number of user names/passwords that enter the router
PPP pap sent-username initiates remote PAP support on an interface and uses Sent-username and password during PAP request packet validation for the same layer
Protocol defines an IP routing protocol that can be RIP, an internal Gateway routing protocol (IGRP), Open Shortest Path First (OSPF), or an enhanced IGRP
PWD Displays the current device name
Reload shutting down and performing a cold start, restarting the operating system
Rlogin to open an active network connection
Router is defined by the first IP routing protocol as the routing process, for example: Router RIP select RIP as the routing protocol
Router Igrp initiates a route selection process for IGRP
Router RIP Select RIP as routing protocol
RSH executes a remote command
SDLC sends SDLC test frames
Send a message on the TTY line
Service password-encryption Password Encryption
Setup runs the Setup command
Show display run System Information
Show Access-lists Displays the contents of all current ACLs
Show buffers Display cache statistics
Show CDP entry displays information about neighboring devices listed in the CDP table
Show CDP interface display Open CDP interface information
Show CDP neighbors shows the results of the CDP lookup process
Show Dialer general diagnostic information for serial interfaces set up for DDR (digital data receiver)
Show Flash shows the layout and content information for Flash
Show Frame-relay LMI displays statistics about the local management interface (LMI)
Show Frame-relay map shows the current map entry and information about the connection
Show Frame-relay PVC Displays statistics about the permanent virtual circuit (PVC) of the Frame Relay interface
Show hosts displays a list of cache names and addresses
Show interfaces displays statistics for all interfaces set on the router and access server
Show interfaces shows the status of all interfaces configured on the router
Show interfaces serial displays information about a serial port
Show IP interface lists a summary of IP information and status for an interface
Show IP interface lists the status and global parameters of the interface
Show IP protocols shows the parameters and current status of the active routing protocol process
Show IP route shows the current status of the routing table
Show ip router display IP routing table information
Show IPX interface displays the status of the IPX interface set by the Cisco IOS software and the parameters in each interface
Show IPX route displays the contents of the IPX routing table
Show IPX servers display list of IPX servers
Show IPX traffic shows the number and type of packets
Show ISDN Active displays information about the current call, including the called number, the time it took to establish the connection, the automated Operation Control (AOC) charge unit used during the call, and whether to provide AOC information during the call and at the end of the call
Show ISDN Ststus shows the status of all ISDN interfaces, or the state of a specific digital signal link (DSL) or the status of a specific ISDN interface
Show memory shows the size of the router's RAM, including the size of the free memory
Show processes shows the process of the router
Show protocols protocol for display settings
Show protocols shows the configured protocol. This command shows the status of any configured layer 3rd protocol
Show Running-config Displays current configuration information in RAM
Show Spantree display spanning tree information about virtual local area networks (VLANs)
Show stacks monitors and interrupts the use of the stack by the program and displays the reason for the last reboot of the system
Show Startup-config Display the startup configuration file in NVRAM
Show Ststus shows the current status of ISDN lines and two B-channels
Show version displays the configuration of the system hardware, the version of the software, the name and source of the configuration file, and the boot image
Shutdown close an interface
Telnet to open a telect connection
Term IP Specifies the format of the network mask for the current session
Term IP netmask-format Specifies the format of the netmask display in the show command output
Timers basic controls how much time the IGRP sends the update information
Trace Trace IP Routing
Username password Specifies the password that is used during CHAP and PAP caller authentication
Verify Test Flash files
Where Displays active connections
Which-route OSI routing table find and display results
Write run configuration information written to memory, network or terminal
Write Erase is now replaced by the copy startup-config command
X3 setting the X.3 parameter on the pad
Xremote into Xremote mode
This article is from 51CTO. COM Technology Blog

Soft routing Configuration Related commands