Highlights about Alpha router Installation

The method for installing the Alpha router has previously been introduced to you. Today, we try again to better understand the vulnerability and the internal connection between the vulnerability and function. Recently, it was found that Cisco Wireless Router allows hackers to easily access the network configuration page of the router.

Problem description:

How to install the Alpha GR55 Wireless Game router? I bought an Alpha GR55 Wireless Game router, but I don't know how to install it?

Alpha router installation satisfactory answer:

1. Make sure that your computer can access the broadband network normally.

2. You need to find the IP address of your router in the manual, which is 192.168.0.1 or 192.168.1.1.

3. click Settings> network connection> Local Connection> Properties> Configuration> advanced> change the Link speed/Duplex mode option to 10 Full mode, and click OK! This step is important because many low-price routers cannot work if they use auto mode or 100 Full mode ).

4. click Settings> network connection> Local Connection> Properties> Select Internet protocol TCP/IP) → properties → select to use the following IP address → fill in 192.168.0.2 in the IP address if your router IP address is 192.168.0.1, fill in the electronic mask 255.255.255.0 Default Gateway fill in 192.168.0.1 if your router IP address is 192.168.1.1) fill in 192.168.1.2, fill in the electronic mask 255.255.255.0 Default Gateway fill in 192.168.1.1. Enter 211.95.193.97 as the preferred DNS server and 202.96.128.68 as the backup DNS server.

5. Enter the vro IP address on the address chain, and fill in the Logon account and password of the broadband access according to the instructions. As a result, I went surfing.

Problem description:

I recently bought an Alpha router and cannot access the Internet after it is installed. How can I configure it?

Alpha router installation satisfactory answer:

You have to check that there are settings in the manual. If you don't understand them, ask again. First, you should enter the host interface. The IP address should be 192.168.18.1. Please try again according to the wizard. You need to set the IP address to 192.168.18.X at the beginning, and set it to 192.168.18.1 with the IP address range and host of the vro.

Alpha router installation satisfactory answer:

I am also using this router. First, set your own ip address 192.168.18.2, dns: 255.255.255.0, and Gateway: 192.168.18.1 in the Local Connection Properties-General-TCP/IP. Save the settings and open ie. in the address bar, enter: http: // 192.168.18.1. Enter the vro logon interface and enter the user name and password (the default user name is admin and the password is admin ). Click "Setup Wizard"-"adsl virtual dial-up pppoe". Press "Next", enter your internet account and password, and note that the password is case-sensitive.) Click "Next" and save. Click Connect in the system status to connect to the Internet. Manually configure the IP Address:

A. Select the specified IP address on the IP address page. The default IP address of this product is 192.168.18.1. Therefore, use 192.168.18.xxx in the IP address field (the number of xxx is 2-253) and 255.255.255.0 In the subnet mask field.

B. On the gateway page, type the default IP address of the product as 192.168.18.1 in the new Gateway field), and click Add.

C. On the DNS configuration page, select Enable DNS, add the DNS provided by the ISP to the DNS server search sequence, and click Add.

Take Shenzhen as an example. The primary DNS is 202.96.134.133 and the secondary DNS is 202.96.128.68. Please consult your local ISP supplier for your DNS. So far, TCP/IP settings are complete. Note: This step is most easily ignored by users. The IP address is the basis for TCP/IP protocol communication. If the correct IP address is not available, the following steps cannot be performed. Because the factory IP address of the Broadband Router is 192.168.18.1, and its built-in DHCP (Dynamic IP allocation) server has the scope of 192.168.18.100-192.168.18.150, therefore, the IP address of the first workstation to which you apply for a bandwidth router is 192.168.18.100, And the IP address of the second workstation is 192.168.18.101.

If your workstation cannot be rented to 192.168.18.x (x: 100 ~ 150), please check whether your network adapter, network cable, TCP/IP protocol is correct. Note that there is a drop-down list above this window. If you have several NICs or Microsoft "dial-up network adapters" installed ", be sure to select the network card connected to the Broadband Router. Do not select another Nic or "PPP Adapter ". If you have other DHCP servers installed on your network, such as Windows NT with DHCP), Please disable the server first.

Then perform step 2. 1. Check whether the vro settings are correct. 2. Is it because the IE version is too low. 3. It may be caused by poisoning. Step by step check. Isn't it just the installation of an Alpha router? What's the problem! First, enter the route to set the IP address. The default route is http: // 192.168.0.1. Second, select ppoe and enter your ADSL username and password! Next ......