Method One: false recognition
1, when the computer prompts necessary to replace the ink cartridge, the normal steps into the new cartridge.
2, then open: Control Panel-printer-printer Properties-utility-check ink residue. We can see the display ink Yume full, then do not click "OK", not to turn off the printer power.
3, the printer's most right side is the printing ink car, will be pulled to change ink cartridge place. Take out the ink cartridge, put on the original computer tip has "used ink cartridges", loaded cartridges and then pushed to the printer's most right end (will be the ink car back to the same place). Then we see ink remaining ink is still displayed as full, click OK, cartridge can be used.
In addition, if you do not want to use the new cartridge to "guest" so, you can fill the ink cartridge above the chip, with a knife or small screwdriver pry, and then the new chip installed. For more information, please refer to the following.
Method Two: Change the core record
1, in accordance with the procedures for ink cartridges, remove the ink cartridges used in the printer, will be above the seal drilling or tearing, exposing filling ink holes, corresponding to the original ink cartridge inks filled with ink, with transparent cloth sealed (using ordinary compatible ink can be).
2, will be filled with ink on the old cartridge above the chip, with a knife or a small screwdriver pry, and then the new cartridge chip to it installed.
3, will be filled with ink and new chips old ink boxed on the printer, you will see the ink cartridge full ink, and then click "OK."
4, such as cartridges automatically back to the final end of the printer, with a small screwdriver or wire will ink car after the move, then you can drag the ink car to change the ink cartridge place. (Light hands!) It's easy. But never use brute force!!!. ）
5, remove the cartridge, the new chip down, replace the old chip, and then the ink boxed on, pushed to the printer's most right side, and then back to the original ink car, and then click the ink display, you will see the ink cartridges full inking, and then click "OK", at this time filled with ink success
Pson ink-jet printer ink Tips
As the Epson Jet cartridge is separated from the nozzle, it does not have to punch holes, you need only a few disposable syringes can complete the task.
Before adding ink you need to prepare broadband tape, absorbent paper, compatible ink, purified water, disposable syringes. Press the inkjet printer manual to remove the cartridge, and then do the following (see figure below for key steps):
1. Wipe the hole in the bottom of the cartridge with a suction paper, and use a clean broadband adhesive tape (preferably with a thick adhesive layer, such as membrane electrical tape) to seal the nozzle.
2. The position of the label on the cartridge can be vaguely seen two small holes, the first hole from the edge of 1cm or so, the second hole and the first hole distance 1.4cm. Use disposable syringes carefully puncture the plastic film (hard to control very small), the first hole for the ink-filling hole, the second hole for the vent hole.
3. Use disposable syringe to absorb about 5ml of ink liquid, will be out of the ink hole up, and tilt 45 degrees to prevent ink from the top of the cartridge at the end of the balance hole overflow.
4. Inject ink: The disposable syringe in the ink liquid slowly into the ink hole, the ink-filling action to be quick after slow, repeated operations several times, until the completion. At the same time, through the transparent plastic shell on the left side of the cartridge, the ink will be note to the ink cartridge capacity of 4/5, should not be too full, and then wipe the ink with absorbent paper near the ink solution.
5. When the cartridge is loaded into the printer, pay attention to the cartridge inserted into the stent, the back must be close to the bracket, only the position is installed, cartridge lock rod can be gently pushed into place. If the handle is blocked, the ink cartridge position is not, at this time, can loosen the lock rod, while using the left hand to move the ink cartridge up and down, side with the right hand gently push the lock rod, feel in place.
6. Finally, open "My computer → printer → properties → control center", into the "clean print head", after one or two times of cleaning, and to ensure that the air out of the mouth, and then print a test page, you can use.
If you want to add color ink can also, but a little cumbersome steps, three times to inject different colors of ink.
It must be emphasized that: there are some small groove on the box-vent ditch, part of the label below, in order to ensure that the ink cartridge internal and external atmospheric pressure, in the adhesive tape can not be completely sealed, otherwise it will not print.
Current 1/2 page
12 Next read the full text
