Link aggregation cannot be configured on the vsphere network only at the switch end

Netizen aa11:01:36
Hello, Miss Wang.
What's the problem?
650) this.width=650; "src=" http://s3.51cto.com/wyfs02/M01/83/2F/wKioL1dstWHgLBQvAAHIMijdcQY349.jpg "/>
Wang Chunhai 11:03:54
The network or gateway you configured is incorrect
Or these two esxi networks are out of the way.
Netizen aa11:04:13
Mr. Wang, help me to see the remote can not
Wang Chunhai 11:06:04

Your server NIC, 650) this.width=650; "src=" Http://s3.51cto.com/wyfs02/M01/83/2F/wKioL1dstWKxA5YmAABIUvrMWOI924.png "/>
650) this.width=650; "src=" Http://s3.51cto.com/wyfs02/M01/83/30/wKiom1dstWLReYNiAABb1B27yEk759.png "/>
The switch port to which the property is connected is not
is the access port connected to the switch?
Netizen aa11:09:15
Right
Two sets
Wang Chunhai 11:09:27
You draw a topological map.
Switch and ESXi network connection topology diagram

Netizen Aa11:11:12
I'll draw.
650) this.width=650; "src=" http://s3.51cto.com/wyfs02/M01/83/30/wKiom1dstWOBBXLPAAEfWe39lCI676.jpg "/>

Host ESXi NICs 0 and 1 are vlan501 address 10.10.11.X segment

Nic 5 and 6 are vlan500 address 10.10.10.X network segments, and the switches are aggregated

Wang Chunhai 11:22:37
You have two switches that need to be interoperable.
For example, a 11.7 NIC is connected to the above switch, and 11.8 is connected to the following switch
These two are not going to work, and vsphere will think of partitioning
Netizen aa11:26:41
I made a stack of 2 switches.
Identical to one switch
I'm going in. The main switch can see all the network ports of the standby switch
Netizen aa11:42:06
Miss Wang, I canceled the aggregation of the 2 switches, and there was no error.
Wang Chunhai 12:06:17
Do you have a switch that supports link aggregation across switches?
Netizen aa12:06:49
Support
650) this.width=650; "src=" Http://s3.51cto.com/wyfs02/M02/83/2F/wKioL1dstWPSJ4Y3AAAEGJMHBJI268.png "/>

Wang Chunhai 12:08:05
In vsphere, your LACP has other patterns, have you tried it?
Netizen aa12:08:39
Rui Jie manufacturers say the default is load balancing
Can be tuned into other
Wang Chunhai 12:09:26
Do you do link aggregation at the end of your esxi?
After the switch has done a link aggregation, you do not have the vsphere end
And if you do link aggregation, it's not your way of planning.
I just saw your server Nic a lot faster
You should:
1, 2 network card is managed, this does not do link aggregation
Netizen aa12:10:33
That's it.
Wang Chunhai 12:10:36
Then the 3~8, where the NIC is configured as a distributed switch
To do the link aggregation again,
You're configured on the switch alone, that's not going to work.
Netizen Aa12:11:11
650) this.width=650; "src=" Http://s3.51cto.com/wyfs02/M02/83/30/wKiom1dstWOgH6jyAAACaSu2h44703.png "/>Not aggregation
That's it.
Wang Chunhai 12:11:35
This is load balancing, not link aggregation
Netizen aa12:12:21
If the business NIC does not do the distributed switch, it can only be de-aggregated on the interchange.
Wang Chunhai 12:12:42
Yes
650) this.width=650; "src=" Http://s3.51cto.com/wyfs02/M02/83/2F/wKioL1dstWPyjg3GAAAB7x6cilY527.png "/>http:// Edu.51cto.com/course/course_id-4898.html
This course has
650) this.width=650; "src=" Http://s3.51cto.com/wyfs02/M00/83/2F/wKioL1dstWSRReMIAAEHcPxE7Og967.png "/>
Netizen aa12:13:53
Ok thanks

This article from "Wang Chunhai blog" blog, declined reprint!

Link aggregation cannot be configured on the vsphere network only at the switch end