The difference between a router and a cat, a hub, a switch

A netizen does not know the cat and the router, the hub, the switch difference between them what is different? Computer knowledge Network for everyone to answer:

A cat has at least two ports: one to the telephone line and one to the RJ-45 port (network cable)

Routers are generally one port: RJ-45 but one to connect the network, a LAN

A router and a cat are not the same device

Routers, simple is composed of LAN, and also provide including packet filtering, packet forwarding, priority, multiplexing, encryption, compression and firewall functions.

Cat is modem, Chinese is called: modem.

Simply put the data in your computer into a specific signal and send it over the phone line. It is a device that converts digital signals into analog signals on the telephone network and converts the analog signals received into digital signals.

The router is the policeman in the street, responsible for the traffic diversion and the directions.

Cat, equivalent to translation, a data protocol, translation into another data protocol.

Cat: is actually called the modem, its function is to turn the telephone line signal to the digital signal, passes to the computer, then converts the computer digital signal to the telephone signal transmits out, thus realizes the computer through it and the telephone line on-line.

Router: is a network device. It allows multiple computers connected to it to surf the internet at the same time and the same type of switch and hub that follows, and the difference between the two is that routers can automatically identify packets sent and reached by the address, so as to achieve faster transmission speed (equivalent to The courier company's point-to-point services, fast and accurate)

Switch: is a network device. It can make the computer that connects it compose LAN, if still have proxy server can also realize the Internet function simultaneously. It does not have the router's automatic identification packet to send and reach the address of the function, but it has a higher transmission speed than the hub, because it can also send all the computers connected to the packet, all computers are sharing its bandwidth rate. That is 100M of bandwidth, no matter how many computers are connected, theoretically each computer's bandwidth reaches 100M.

Hub: (here to correct the first floor of the view: The hub to understand the English name of the switch is not appropriate) The hub of the Chinese name should be called a hub, and the above two are the same network equipment, other functions are the same. But it has a bit of a different place: it can only process and send packets to the computer that connects to it, and all computers can only share its bandwidth rate. That is, 100M of bandwidth, if the connection has 20 computers, the actual bandwidth of each computer is only 5 m.

Router setup means that it enables the computer to connect to it automatically on the Internet. That is, the router automatically dialing, and the computer connected to it does not need to dial, only need to boot on the Internet, very convenient. Specific settings to view the router's instructions, each router settings are different.

How to distinguish switches, routers, hubs, and cats is a problem for many novice computers: Let's briefly introduce the difference between these things:

First of all said Hub, that is, hubs. Its role can be simply understood to connect some machines to form a local area network. A switch (also known as a switched hub) works roughly the same as a hub. But there is a difference in performance: the way the hub uses shared bandwidth works, and the switch is the exclusive bandwidth. In this way, when there is a lot of machine or large amount of data, the two will be more obvious. The router and the above two obvious difference, its role is to connect different network segments and find the network data transfer the most appropriate path, can be said that under normal circumstances, individual users need not. Routers are generated after the switch, just as the switch is generated after the hub, so routers and switches are also connected, not completely independent of the two devices. Routers mainly overcome the inability of the switch to route and forward packets.

In general, the main differences between routers and switches are embodied in the following aspects (computer Basics www.pc6c.com):

(1) Different levels of work

The initial switch is the data link layer that works in the OSI/RM open architecture, which is the second tier, and the router begins by designing the network layer that works at the OSI model. Since the switch works on the second layer of OSI (data link layer), it works fairly simply, and routers work on the third layer of OSI (the network layer) to get more protocol information, and routers can make more intelligent forwarding decisions.

(2) Data forwarding based on different objects

A switch uses a physical address or a MAC address to determine the destination address of the forwarded data. The router uses the ID number of the different network (that is, the IP address) to determine the address of the data forwarding. IP addresses are implemented in software that describes the network where the devices are located, and sometimes these third-tier addresses are also called Protocol addresses or network addresses. MAC addresses are usually hardware-led, distributed by the manufacturer of the network adapter, and have been cured to the network card, which is generally not to be changed. IP addresses are usually assigned automatically by your network administrator or system.

(3) Traditional switches can only split the conflict domain, can not split the broadcast domain;

The network segments that are connected by the switch still belong to the same broadcast domain, and broadcast packets propagate across all network segments connected to the switch, which in some cases can lead to traffic congestion and security vulnerabilities. The network segments that are connected to the router are assigned to different broadcast domains, and broadcast data does not go through the router. Although the third layer above the switch has VLAN function, can also split broadcast domain, but each sub broadcast domain is unable to communicate the communication, the communication between them still needs the router.

(4) The router provides the service of the firewall

Routers can prevent broadcast storms by forwarding only packets of specific addresses, sending packet transmissions that do not support routing protocols, and sending unknown destination network packets.

Switches are generally used for lan-wan connections, switches to Network Bridge, data link layer equipment, some switches can also achieve the third layer of exchange. Routers are used for connections between Wan-wan, which can be used to resolve the forwarding groupings between opposite-sex networks, and to use the network layer. They just accept the input grouping from one line, and then forward to another line. These two lines may belong to different networks and use different protocols. Comparatively speaking, the function of the router is more powerful than the switch, but the speed is relatively slow and the price is expensive, the third layer switch has the ability of the switch speed forwarding message and the good control function of the router, so it can be widely used.

At present, the personal comparison of multiple broadband access is ADSL, so the author on the ADSL access to a simple explanation. Nowadays, most of the ADSL cats have routing function (many of the time the factory will be in the factory to block the routing function, because most of the telecom installation is not enabled by the routing function, enable DHCP. Open ADSL Routing function, if the personal Internet or a few of the few through the ADSL itself can be, if the computer more you just need to buy one or more hubs or switches. In view of the fact that the price of hubs and switches is very small and is not a special cause, please purchase a switch. There is no need to pursue high prices, because today's product homogeneity is very serious, my cheapest switch now has no problem. Give you a reference quote, suggest you buy a 8-port to meet the expansion of demand, the general price of about 100 yuan. Connect the switch and all the computers will be connected to the switch. The only thing left to do is to plug each machine's network cable into the switch's interface and plug the cat's network cable into the uplink interface. Then set the routing function, DHCP and so on, you can share the Internet.

Read the above explanation readers should have some understanding of the switches, hubs, routers, the current use of mainly switches, routers, the combination of the use of specific methods can be based on specific network conditions and needs to determine