Two-step Wireless LAN configuration (1)

How does one set wireless lan? Networks are very important for computer enthusiasts. We can share and spread knowledge. For computer enthusiasts, we all know that networks can be divided into wired networks and wireless networks.

Knowledge about wireless LAN Settings:

The fundamental difference between wired and wireless networks is that wired networks are connected to switches through NICs and network cables, while wireless networks are connected to wireless switches through wireless NICs. They have their own characteristics, A wired network is connected to a vswitch through a network cable. The advantage is that the transmission speed is fast and the anti-interference capability is strong. The disadvantage is that the connection is troublesome and requires prior wiring. A wireless network is connected to a vswitch through wireless connection, the advantage is that it is easy to install and requires no prior wiring. The disadvantage is that the transmission speed is slow and the anti-interference capability is poor. Due to the convenience of wireless network installation, many netizens now prefer wireless networks. Especially for some space that cannot be cabled)

Detailed Rules for setting Wireless LAN:

The establishment of a wireless LAN requires a wireless network card and a vswitch for the Wireless AP). If you want to access the Internet, you need to use the wireless router. This article takes the home wireless network as an example, use a wireless Nic and a wireless router.

TP-LINK WR541G 54M Wireless router and DELL 630M notebook, comes with Intel (R) PRO/Wireless 2200BG Network Connection 54M Wireless Network card.

Step 1 of Wireless LAN Settings and vro settings

The current router settings are mostly set through the WEB. Because the router may not be able to use the wireless function before the correct settings are made, we connect to the router through the network cable; first, enter the default IP address of WR541G in the address bar of the browser, 192.168.1.1. The default IP addresses of the vro may be different. Therefore, you can find the default IP addresses in the vro or instructions. Here, you need to note: when setting a router through the WEB, the IP address of the computer connected to the router must be set to the same gateway as the router; if the router IP address of the mouse is 192.168.1.1, you can set the IP address of the computer to 192.168.1.2 --- 192.168.1.255.

You can set the IP address of a computer as follows:

When the NIC Driver is correctly installed on the computer, select Control Panel> network connection> local connection, as shown in figure

Select Internet protocol TCP/IP), click Properties -- select to use the following IP address; IP address input: 192.168.1.2 --- any address between 192.168.1.255, enter 192.168.1.2 here, subnet mask input 255.255.0, enter 192.168.1.1 as the IP address of the router in the default gateway. For example

Enter the IP address of the vro in the address bar of the browser and set 192.168.1.1 to enter the WEB configuration interface of the vro. Generally, the router requires the administrator password when entering the WEB Settings interface. For the first time, enter the original password as instructed.

Enter the correct user name and password To Go To The vro settings page.

TP-LINK router setup and installation is simple, and cost-effective is also good, especially suitable for the family network; the mouse used a few TP-LINK router, I feel good. Besides, Chinese people must also support Chinese goods.
If you only want to set up a vro, you only need to select the setting wizard and configure the network according to your Internet access mode to implement the routing function. For the Internet access method, please select according to your own situation. Here, we use the most common domestic ADSL virtual dial-up PPPoE dialing method as an example.
Select ADSL virtual dialing PPPoE), click Next, and enter your account name and password. If you do not know, please contact your local IP service provider. Click Next to enter the Wireless Settings interface, the TP-LINK is wireless by default open, because we this article mainly introduces Wireless Settings, so if the wireless function of this setting interface is not open, choose to open, click Next to complete vro settings. Because a new vro is set, the vro will be re-connected. If the router is started correctly and the running status on the interface is set, the current status of the vro should be correctly displayed. If the WAN port status shows an error, set an error for you. Set it again.

The current status after the vro is correctly connected

If you want the following clients to easily configure the network, you can enable the DHCP service in the vro, the TCP/IP protocol for all computers in the LAN connected to the router is set to "automatically obtain the IP address", and the router can automatically configure the network for each machine. In this way, you do not need to specify IP addresses for each machine. Of course, you can also manually specify IP addresses for each computer when the DHCP service is enabled.