Others

We have discussed a lot about NFS. I wonder if you have any questions. Today, we will mainly explain how to set NFS ports. In many network environments, different port settings may cause different functions. To use NFS in a firewall environment,

In the network, the storage and sharing methods of files and resources are very complex. It can only be completed under the joint cooperation of multiple protocols. Here we will introduce the use of the NFS protocol. What are the issues that need to

NFS will certainly be widely used. In addition to network and storage applications, it can often be applied to monitoring modules. Here we will discuss the content of NFS mounting. In the previous article, we have also introduced related scripts.

In the NFS service application, we will encounter mounting usage and configuration. Many of my friends are not familiar with this content. Therefore, we will introduce the content in detail here, hoping to help you understand this knowledge. Note:

The development of the network is immeasurable. Now we have transitioned from IPv4 to IPv6, So how should we adapt to the routing, especially the RIP Protocol? With the rapid development of the Internet, the network scale expands rapidly, the amount

In many systems, NFS services are disabled. Therefore, we need to manually enable and configure them. The settings of NFS Server and NFS Client are described in detail in this article. We hope that you will be able to master this part of

NFS Server can share files. This feature is also added to other software services. So what is NFS? NFS was initially developed by Sun Microsytem in 1984. Its primary function is to allow UNIX computers on the network to share directories and files.

Next, let's take a look at the list of RIP route tables. How can we interpret long strings of information? Let's take a closer look. Section 1st of the RIP route table list: route table under r12001 R3#sh ip route rip  

In some network security scenarios, We need to disable DHCP to improve the security level. Disable DHCP: Set the wireless router security function. The implementation of the wireless route security function is a common problem. How to Implement the

In some network faults, we often encounter some DHCP server problems. In a large LAN, the IP address of the workstation is usually obtained dynamically from the DHCP server, which can effectively save IP Address Resources; however, during the

DHCP server debugging is very important in the network. It manages the allocation and management of IP addresses. In a large network, you need to allocate various addresses (IP addresses, subnet masks, gateways, DNS addresses, and WINS server

In terms of networks, security has always been a concern for us. Here we will mainly explain the protection and security issues related to the DHCP server. To improve network management efficiency, network administrators often set up and install

In enterprises, routers are used to build DHCP servers. Let's take a look at the relevant content based on the following actual application case. Project requirements: XX enterprise has three departments, which are divided into VLAN for the three

We will fully consider security. In particular, we need to pay attention to network security. How can I disable the DHCP service? Disable DHCP: Set the wireless router security function. The implementation of the wireless route security function is

DHCP is very useful. We can see this function in the construction of many enterprise networks. But how can we reduce security threats in some designs that do not use this function? Here we can try to disable the DHCP function. What should I do?

In terms of routers, I believe everyone knows CISCO. Do you know about its DHCP server configuration? Here we will introduce in detail the dhcp configuration of the CISCO router. Configure the vrodhcp as a dhcp server to allocate IP addresses to the

We have introduced the basic concepts and meanings of DHCP Relay. For this part of knowledge, we will focus on configuration content this time. Now let's take a look at the network environment described here. Functional requirements and networking

DHCP servers, once used, all know that when we configure them, we need to set them in various stages. For TCP/IP networks, basic network configurations, such as IP addresses, subnet masks, default gateways, and DNS, must be configured for each

I believe you have mastered the concept of PPP Multilink. Here we will focus on the configuration of PPP Multilink. So this article uses two E1 bindings to implement 4 m data transmission. Now we will write the document for your reference. Network

It is common to configure DHCP content on a vswitch. Here we will explain how to configure the DHCP Server of the H3C switch. In the subsequent articles, we will also introduce other configurations and hope you will be able to pay attention to them.