It is very important for Cisco router users to learn about commands for password recovery of Cisco routers. For many beginners, the ROM Monitor of Cisco routers is often unfamiliar or even daunting for a simple reason, first, we do not often use this mode and are not familiar with its related operations; second, Operat
For many beginners, using cisco rommon to maintain a vro, the ROM Monitor of a cisco router is often unfamiliar or even daunting. The reason is simple. First, we do not often use this mode, I am not familiar with the related operations. Second, Operation errors in ROM Monitor mode often cause fatal damage to the vro (such as destroying the IOS file in flash, lead
The command line port of a cisco router uses a hierarchical structure, which requires logging on to different modes to complete detailed configuration tasks. From a security perspective, cisco IOS divides EXEC sessions into USER mode and privileged mode.
Features of the USER mode:
In USER mode, only basic monitoring commands are allowed. In this mode, the confi
In the BGP Route Selection protocol, you can filter the BGP Route Selection and update. To do this, you need to use the prefix list. I. prefix list features: (1) it can be incrementally modified. We know that we cannot delete an entry in the general access control list, if you want to delete an entry in the list, you can only delete all the entries in the list. In the prefix list, you can delete or Add an entry separately. Www.2cto.com (2) and prefix list can be used in
access vlan 4
Switch (config-if) # no shutdown
Switch (config-if) # exit
Switch (config) # interface f0/3
Switch (config-if) # switchport mode trunk sets this port to relay mode)
Switch (config-if) # no shutdown
Witch (config-if) # exit. You can directly use ctrl + z or end to exit the privileged mode)
2. Configure single-arm routing on vrocisco Cisco 2611)
Router # con
There are many things worth learning about the configuration mode of a Cisco router. Here we mainly introduce the mode of user execution and privilege of a Cisco router. Ping is the most commonly used troubleshooting command. It consists of a group of ICMP response request packets. If the network runs normally, a group
Basic configurations of Cisco routers and switches: www.2cto.com Router> \ enter the user mode Router when the vro is started> enable \ type the command to enter the Router mode # \ This display mode indicates that the Router mode has been entered # configure terminal \ type
As the core device of network communication, Cisco routers are widely used. The following is my experience in practice:
Control port interface practices and connections
Connect one end of the control cable RJ45 in the Cisco2500/1000 series router accessories to the Cisco CONSOLE port, and the Cisco7000/4000 series router
This article describes how to configure a vswitch for a CISCO 3550 router and how to configure access control for a MAC address.
In network management, users often encounter this situation: some users violate management regulations and modify their own IP addresses without permission to access restricted resources. Such behavior not only undermines information security rules, but may also cause network comm
First, the Cisco router to introduce the memory
A router is similar to a computer in that it also has memory, operating system, configuration, and user interface, and the operating system in Cisco routers is calledInternet Operating System (Internetwork operating system) or iOS. The following is mainly about the stora
Cisco router Startup ProcessThe Startup Process of a Cisco router is divided into four main stages: 1. execute POST 2. load the bootstrap program 3. search for and load Cisco IOS software 4. find and load the startup configuration file, or enter the setup Mode 1. executing P
This article describes in detail how to skillfully set the speed limit for commonly used Cisco routers, and provides detailed operation steps. I hope this article will help you.
The so-called speed limit is to set the ACL Access Control List on the router) to block the port used by the Service, so as to prevent the normal operation of the service. For the btsoftware, we can try to seal its port. In general,
Everyone knows that the Cisco router ACL plays an important role in the security policy of the Cisco router. Therefore, it is essential for everyone to master these knowledge points. In fact, this content is involved in many places. Access List) is an ordered statement set. It is a Sort table that allows or rejects pac
Before giving you a detailed introduction to the Cisco router ACL, first let everyone know about the ACL, and then give a full introduction to the mask to block the scam attack. Wildcard-mask wildcard mask in the Cisco router ACL Access Control List ).
Brief: The wildcard mask (or anti-mask) used in the
configure NAT, a traditional IP Nat inside/outside mode, a NAT Virtual Interface (NVI) way, configure IP NAT enable under the interface, two ways can coexist simultaneously
---can successfully do NAT first need to exist routing, another must be from the IP Nat inside interface, from the IP Nat outside interface, or from an IP Nat enable interface to enter from another IP NAT enable interface out
---for the traditional way of l2l VPN configuration,
Analysis of Cisco router IOS backup and recovery
Introduction:
I. Wiring
Serial Interface-> console and pc Nic interfaces-> F0/0
// The IP address of the PC and the F0/0 interface (of course, other interfaces can be connected to the network cable). The IP address can be in the same network segment. You can also use an Internet ip address!
Ii. Tools
3 CDaemon (tftp server) and CRT (access routing tool)
Iii.
Here we will mainly introduce the configuration and initial installation of Cisco routers. Describes how to configure Cisco router settings and remote access, this article discusses how to use the DHCP service function of the internal network to allocate address information for users who remotely dial in and how to troubleshoot common vro faults.
1. Initial insta
Basic configuration of the Cisco PT Simulation Experiment (10) routerExperimental Purpose :Mastering several common configuration methods of routersFamiliar with different command line operation modes of routersBasic configuration commands for the Palm-lift routerExperimental Background : as a network administrator, you first in the equipment room to the router after the first configuration, I hope in the f
The question about the Cisco router interface is described in the following four steps. Based on the demonstration in the image, I believe that we should be able to clearly understand the question about the interface. You can configure a serial interface through a virtual terminal. to configure a serial interface, follow these steps:
1. In Global mode, enter the command "interface serial 0" to enter the ser
Some Suggestions on preventing distributed denial of service (DDoS) attacks on Cisco Routers
1. Use the ip verfy unicast reverse-path network interface command
This function checks each packet passing through the router. In the CEF (Cisco Express Forwarding) Table of the router, the
The content source of this page is from Internet, which doesn't represent Alibaba Cloud's opinion;
products and services mentioned on that page don't have any relationship with Alibaba Cloud. If the
content of the page makes you feel confusing, please write us an email, we will handle the problem
within 5 days after receiving your email.
If you find any instances of plagiarism from the community, please send an email to:
info-contact@alibabacloud.com
and provide relevant evidence. A staff member will contact you within 5 working days.