configure nat on cisco router

The static one-to-one NAT Global Address of the router is also used for PAT and natpat I. Description Handle a fault. A host performs one-to-one static NAT on the Cisco router. The host can log on to the device through the NAT add

Test environment: Cisco Router Intranet interface F0/1:192.168.1.1 255.255.255.0 External network Interface f0/0:10.0.0.1 255.255.255.0 Server ip:192.168.1.100 First configure on the router: Router>en #进入特权模式 router#conf T #进入全局配置模式 Enter configuration commands, one

network address translation (nat) Protocol to support network connection sharing among Wireless LAN users. This is a useful feature in the soho environment. They may also have basic firewalls or information packet filters to prevent port scanning software and other attacks against broadband connections. Finally, most wireless routers include an Ethernet converter with four ports to connect several wired PCs. This is very convenient for managing route

formatRouter (config) #ip route 2.0.0.0 255.0.0.0 1.1.1.2; Static Route exampleRouter (config) #ip Route 0.0.0.0 0.0.0.0 1.1.1.2, default route exampleDynamic routing:Router (config) #ip routing; Initiate route forwardingRouter (config) #router rip; start RIP routing protocol.Router (config-router) #network; set up publishing routesRouter (config-router) #negihb

This article uses a specific example to illustrate how to configure the access to ADSL through the vro. What problems should we pay attention to during access? The following articles will benefit you a lot. Note: In this case, a common adsl modem and a cisco 25001841) router (dual Ethernet port) and IOS 12.2 (15) T need to be used to connect to the China Telecom adsl PPPoE, able to achieve LAN Internet shar

With the development of China's routing industry, its application is also more extensive, especially the application of routers and firewalls. Here we mainly explain the security configuration of NetEye firewall and Cisco router. Firewall has become a key part of enterprise network construction. However, many users think that Cisco routers already exist in the ne

Maybe many people do not know the actual application of the NetEye firewall and the Cisco router. Next we mainly analyze the security problems of the NetEye firewall and the Cisco router. Firewall has become a key part of enterprise network construction. However, many users think that there are already routers in the n

Analysis of Cisco Broadband Access configuration method China Telecom's bandwidth is 2 M and the assigned fixed IP Address: 202.249.11.101 subnet mask: 255.255.255.255.248 Gateway: 202.249.11.20Planned LAN address range: 192.168.0.2-192.168.0.254 subnet mask: 255.255.255.248 Gateway: 192.168.0.1The vro provides a 1721 M Adaptive port for Cisco 10/100. Next, we need to configure a 1ENET expansion card with

First, give an environment:Cisco router Intranet interface s1/0: 192.168.1.1 255.255.255.0Internet interface s1/1: 10.0.0.1 255.255.255.0Server ip Address: 192.168.1.100First telnet to the vrotelnet:User Access Verification Username: cisco # enter the user namePassword: # enter the PasswordRouter> en # Enter privileged ModePassword: # enter the privileged mode PasswordRouter # conf t # enter global configur

applications, such as http url, DNS, FTP, and VoIP. At the same time, it can also be defined, to enable NBAR to support many emerging network applications. For example, peer2peer tool.PDLM can be downloaded from Cisco websites, and PDLM can be used to limit malicious traffic on some networks. CISCO provides three PDLM modules on its official website: KAZAA2.pdlm and bittorrent. pdlm. emonkey. pdlm can be u

Configure the PPPoE configuration for connecting a CISCO router to an ADSLmodem through the PPPoE configuration: hostnamebjsite! Ipsubnet-zeronoipdomain-lookup! Vpdnenablenovpdnlogging! Vpdn-group1request-dialinprotocolpppoe! Interfaceethernet00ipaddh Configure PPPoE for connecting a CISCO router to an ADSL modem using

This article uses VPN technology to achieve interconnection between two parts of the network, simulate ISP, close to practicality, the article mainly shows us the specific operation steps, mainly the input of basic commands. In this experiment, we use the Cisco 2600 router and VPN technology to achieve the network interconnection between one branch and two parts. To stay close to practicality, we still use

Implementation of ADSL access using the cisco 2500 router Description: This case is Beijing Telecom's adsl PPPoE access. A common adsl modem and a cisco 2500 router (dual Ethernet port) are required, and IOS 12.2 (15) t, can achieve LAN Internet sharing. in this case, the configuration is divided into seven steps: www.

Configure PPPoE for connecting a CISCO router to an ADSL modem using the Cisco router: hostname bjsite! Ip subnet-zero no ip domain-lookup! Vpdn enable no vpdn logging! Vpdn-group 1 request-dialin protocol pppoe! Interface Ethernet0/0 ip address 192.168.0.1 255.255.255.0 ip nat