The Android system is a Linux system, and we can use the Linux command Mouunt to get a Linux mount directory. The directory that the obtains from the command I did not traverse, and if you still cannot get it, you can iterate through all the directories that the mount has been to.
filesdcard; @SuppressLint ("Sdcardpath") publicfilegetsdcardfile () { if (sdcard!=null) {
returnsdcard; } List
However, th
, help, the most critical is the last sentence, where auto represents the first partition mounted SD card, followed by the Vold monitoring path, when inserting SD,/DEVICES/PLATFORM/S3C-SDHCI.0/MMC_HOST/MMC0 There will be more than one folder under the path, please confirm the corresponding path of your hardware platform.
Finally, there are a few things to focus
1. Manually mount/unmount the USB drive, SD cardFor ARM Linux, the first time you use a USB flash drive or SD, this file directory is not directly accessible, we need to mount it, and then the next use can be directly used. Through the online search data, now the U disk in the Liunx under the method of recording down;S
1. The app is installed under/mnt/sdcard by default. If your SD card is not mounted, the system will prompt you to request an SD card or damage SD card, so now you can go to this/mnt/sdcard or/sdcard (the two are in the same direc
(1) Verify that the Linux system on the board recognizes the SD card via the #fdisk-l commandMP805M board is displayed after inserting the SD cardSD30 slot is without WPMmc1:new High speed SD card at address 5bc0MMCBLK0:MMC1:5BC0 sd02g 1.83 GiBMmcblk0:p1[/]# fdisk-lDisk/dev/
First refer to these blogs to do some understanding: http://linux.chinaunix.net/techdoc/install/2009/11/18/1144936.shtmlHttp://www.cnblogs.com/leaven/archive/2010/09/17/1828896.html, can also Baidu mdev.conf view other articles.The kernel is sure to support Mdev and hotplug features.Etc directory to have this file mdev.conf, the content is as follows (other similar):SD[A-Z][0-9] 0:0 666 @/etc/hotplug/usb/udisk_insertsd[a-z] 0:0 6
}elseif (Intent.getaction (). Equals ("Android.intent.action.MEDIA_REMOVED")// various non-mounted conditions || Intent.getaction (). Equals ("Android.intent.action.ACTION_MEDIA_UNMOUNTED") || Intent.getaction (). Equals ("Android.intent.action.ACTION_MEDIA_BAD_REMOVAL")) { ImagePath = Android.os.Environment.getDataDirectory ();// your local path } } }; // Select the action you want to monitor in the intentfilter intentfilter intentfilter =newintentfilter (intent.action_media_mounted); int
in Linux we often use U disk, SD card mount problem, each time manually mount or uninstall is very troublesome, we can take the following methods to achieve automatic mount or uninstall U disk, SD
After the source code of 2.3 is downloaded and compiled, the boot simulator usually does not have a storage card (SD card) mounted, which leads to a problem: many tests that require the SD card cannot be done, for example, you want to use traceview to track your program (you
Tags: fdisk sdcard l command SD card img font. com span DTBFirst use the Fdisk–l command to view the SD card's partitionYou can see that the SD card has three partitions, the first partition is the FAT32 system, the main storage of the kernel img files and DTB files, the sec
SD card mounting File System: VFS: Cannot open root device "mmcblk0p2" solves the problem of using the initramfs file system. linux can run properly and read and write SD cards normally. However, it cannot be mounted when it is mounted on the SD card. The information about b
installed at an offset, the SD card may become unavailable.3) In addition, if the SD card is unavailable, we can pull out the SD card to see if there is dust on the chip. If yes, clear the SD
Debugging related to SD card is often encountered in andorid development, such as MP3 files and image files. When developing a simulator, you can simulate an SD card through a hard disk. The specific method is:
(1) Create an SD card
Like most of my friends, I used to only use the SD card SPI mode. This mode is simple and can be implemented on most single-chip computers without the need for CRC verification. The SD mode can achieve simultaneous transmission of four data lines, which has a great advantage over the SPI mode in terms of speed. Therefore, this project selects the
I. Soil EIGHT practices:Once the SD card is plugged into the system, the kernel will automatically create the device file under/dev/: SDcard. But sometimes the user in the dial out before the card and no umount, the second card in the system created is not sdcard device files, but mmcblk0, MMCBLK1P1, MMCBLK2P1, or MMCB
1. Introduction
To install the application on the SD card and TF card, the android system does not support it by default. It has only one ASEC mount point:/mnt/secure/ASEC. In my system, this mount point is occupied by/mnt/sdcard, so the TF
memory card all the old partitions, in the creation of new partitions to the full capacity of FAT32 can, and finally remember point "application"!
Second, mobile phone installation LINK2SD
LINK2SD A can make Android more than 1.6 system users to move applications to the SD card, need root support, in fact, is LINK2SD
[Description]
How to automatically install the APK on the external SD card to the memory card of the mobile phone when the mobile phone is started for the first time.
[Solution]
Design Concept:
1.Put the APK to a directory on the SD card, suchApks_preinstallDirectory.
(For
The content source of this page is from Internet, which doesn't represent Alibaba Cloud's opinion;
products and services mentioned on that page don't have any relationship with Alibaba Cloud. If the
content of the page makes you feel confusing, please write us an email, we will handle the problem
within 5 days after receiving your email.
If you find any instances of plagiarism from the community, please send an email to:
info-contact@alibabacloud.com
and provide relevant evidence. A staff member will contact you within 5 working days.