Routing re-release configuration related commands Router> enRouter # confrouting from terminal, memory, or network [terminal]? Enter configuration commands, one per line. end with CNTL/Z. router (config) # host R4R4 (config) # int lo4 % LINK-5-CHANGED: Interface Loopback4, changed state to up % LINEPROTO-5-UPDOWN: Line protocol on Interface Loopback4, changed state to upR4 (config-if) # ip add 192.168.4.1 255.255.255.0R4 (config-if) # no shutR4 (config-if) # exitR4 (config) # int s0/1/0R4 (config-if) # ip add 192.168.45.4 255.255.255.0R4 (config-if) # Clock rate 56000R4 (config-if) # no shut % LINK-5-CHANGED: Interface Serial0/1/0, changed state to downR4 (config-if) # exitR4 (config) # router ripR4 (config-router) # net 192.168.4.0R4 (config-router) # net 192.168.45.0R4 (config-router) # end % SYS-5-CONFIG_ I: configured from console by consoleR4 # Router> enRouter # confConfiguring from terminal, memory, or network [terminal]? Enter configuration commands, one per line. end with CNTL/Z. router (config) # host R5R5 (config) # int s0/1/1R5 (config-if) # ip add 192.168.45.5 255.255.255.0R5 (config-if) # no shutR5 (config-if) # % LINK-5-CHANGED: Interface Serial0/1/1, changed state to up % LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/1/1, changed state to upR5 (config-if) # exitR5 (config) # int s0/1/0R5 (config-if) # ip add 192.168.56.5 255. 255.255.0R5 (config-if) # clock rate 56000R5 (config-if) # no shut % LINK-5-CHANGED: Interface Serial0/1/0, state changed to downR5 (config-if) # exitR5 (config) # router ripR5 (config-router) # net 192.168.45.0R5 (config-router) # redistribute Kerberos 4567 metric 10R5 (config-router) # exitR5 (config) # router VPN 4567R5 (config-router) # net 192.168.56.0R5 (config-router) # redistribute rip metric 1544 20000 255 1 1500R5 (conf Ig-router) # end % SYS-5-CONFIG_ I: Configured from console by consoleR5 # Router> enRouter # confConfiguring from terminal, memory, or network [terminal]? Enter configuration commands, one per line. end with CNTL/Z. router (config) # host R6R6 (config) # int s0/1/1R6 (config-if) # ip add 192.168.56.6 255.255.255.0R6 (config-if) # no shut % LINK-5-CHANGED: Interface Serial0/1/1, changed state to upR6 (config-if) # % LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/1/1, changed state to upR6 (config-if) # exitR6 (config) # int s0/1/0R6 (config-if) # ip add 192.168.67.6 255. 255.255.0R6 (config-if) # clock rate 56000R6 (config-if) # no shut % LINK-5-CHANGED: Interface Serial0/1/0, changed state to downR6 (config-if) # router VPN 4567R6 (config-router) # net 192.168.56.0R6 (config-router) # % DUAL-5-NBRCHANGE: IP-EIGRP 4567: Neighbor 192.168.56.5 (Serial0/1/1) is up: new adjacencyR6 (config-router) # redistribute ospf 4567 metric 1544 20000 255 1 1500R6 (config-router) # exitR6 (config) # rou Ter ospf 4567R6 (config-router) # net 192.168.67.0 0.0.0.255 area 0R6 (config-router) # redistribute VPN 4567 subnets R6 (config-router) # end % SYS-5-CONFIG_ I: configured from console by consoleR6 # Router> enRouter # confConfiguring from terminal, memory, or network [terminal]? Enter configuration commands, one per line. end with CNTL/Z. router (config) # host R7R7 (config) # int lo7 % LINK-5-CHANGED: Interface Loopback7, changed state to up % LINEPROTO-5-UPDOWN: Line protocol on Interface Loopback7, changed state to upR7 (config-if) # ip add 192.168.7.1 255.255.255.0R7 (config-if) # no shutR7 (config-if) # exitR7 (config) # int s0/1/1R7 (config-if) # ip add 192.168.67.7 255.255.255.0R7 (config-if) # no shut % LINK-5-CHANGED: Interface Serial0/1/1, changed state to upR7 (config-if) # % LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/1/1, changed state to upR7 (config-if) # exitR7 (config) # router ospf 4567R7 (config-router) # net 192.168.7.0 0.0.0.255 area 0R7 (config-router) # net 192.168.67.0 0.0.0.255 area 0R7 (config-router) # end % SYS-5-CONFIG_ I: configured from console by consoleR7 #00: 02: 39: % OSPF-5-ADJCHG: Process 4567, Nbr 192.168.67.6 on Serial0/1/1 from LOADING to FULL, Loading Done