FAQs about one-click USB flash drive system installation

FAQs about one-click USB flash drive system installation
1. What is the one-click USB flash drive installation system?

One-click USB flash drive is a one-step boot disk that can be created as a USB flash drive with winpe. It completely solves the trouble of re-installing the system without the optical drive.

2. Why is the USB flash disk empty after I installed it with a one-click USB flash drive?
The successful USB flash drive has the following features:
The one-click USB flash drive system tool uses the hidden partition technology. It is normal to see the content in it. You can compare the size of the original USB flash drive to see if the size is more than 100 MB less, if yes, It is created successfully.

3. What kind of mobile devices does one-click USB flash drive support?
Currently, mobile storage devices such as USB flash drives, memory cards, mp3/mp4, mobile hard disks, and mobile phone cards are supported.

4. How many USB disks does one-click USB flash drive support?
Supports MB and above of all capacity, up to 2 TB.

5. How can I use a one-click USB flash drive to install the system tool?
Note: back up your data before use; otherwise, data loss may occur after the USB flash disk is formatted.

6. After the preparation is complete, the USB flash drive prompts formatting? 
USB flash drives can be pulled out. Re-insert

7. How to Choose USB-HDD and USB-ZIP?
It mainly depends on the Mode Supported by your computer. Most of them should choose USB-HDD.

8. Why does my one-click USB flash drive fail to run?
Required Conditions:
1. When running, you need to have administrator permissions, that is, administrator
2. Your USB flash drive capacity is too small
3. When the 360 security prompt is displayed, click to allow operations on this tool.
4. Check whether your USB flash drive has been created in mass production. If the flash drive has been created in mass production, use it after the recovery.

9. Why cannot I install the system after I enter pe?
Make sure that your system GHOST file exists and can be used. If onekey is used, check whether your system file is decompressed.

10. What should I do if I want to restore the space in the USB flash disk after use?
Open the software and click "Restore USB flash drive.

11. What tools are included in the integrated winpe?
Basic tools include disk repair, data recovery, system restoration, disk detection, memory detection, hard disk partitioning, and Internet access.

12. How long does winpe wait?
Depending on the computer configuration model, it generally takes 1-3 minutes, depending on your memory and usb interface.

13. Why can't I enter the system PE with a one-click USB flash drive?
1. You may have downloaded the USB flash drive system tool from other websites. Please download it from the one-click studio official website.
2. pe requires that your memory size be at least 512 mb

14. How can I set up a USB flash drive boot system?
The best way is to find your motherboard user manual. Of course, we have released some bios settings on the official website.

15. What should I do if I have a problem installing the system with a one-click USB flash drive?
Please go to the official bbs tutorials and post in the issue area

16. What should I pay attention to if I want to replace the old version with the new version?
Note: before changing the version, please confirm that your data is transferred securely. The new version will automatically clear your old version and install it completely without the need to clear it.

17. Can I use a one-click USB flash drive to install the system-created USB flash drive on another computer?
A one-click USB flash drive can be applied to any computer.

18. Considerations for using one-click USB flash drives for mass production
After you select the second (non-cdrom) Partition when using a one-click usb flash drive for mass production, your usb flash drive will support usb-cdrom, usb-hdd, or usb-zip, start in three modes. If you use a one-click USB flash drive to install the system for a mass-produced USB flash drive, the compatibility may be reduced. It is recommended that you use the production tool to restore the usb flash disk to the normal state, that is, remove the usb cdrom, and then use a one-click usb disk to install the system usb disk. The compatibility will be greatly improved.

19. Why can't I find my USB flash drive or mobile hard drive in PE?
You can try to insert a mobile hard disk when it is shut down before winpe is started. If it cannot be identified after it is started, enter disk management to specify a mobile drive letter.

20. Do you have to pay attention to installing the system when using the green leaf [USB boot disk creation tool] for a mass-produced USB flash drive?
When using the green leaf [U disk boot disk preparation tool] to install the system, please select the second (non-cdrom) partition, your U disk will support usb-cdrom, usb-hdd or usb-zip, which can be enabled in three modes. If you use the green leaf [USB boot disk preparation tool] to install the system for a mass-produced USB flash drive, the compatibility may be reduced. We recommend that you use the production tool to restore the usb flash disk to the normal state, that is, remove the usb cdrom, and then use the green leaf [U disk boot disk preparation tool] to install the system usb flash disk. The compatibility will be greatly improved.
Related reading:
One-click USB flash drive _ How to use a USB flash drive to install the system-Windows XP system and Windows 7 system tutorial-one-click USB flash drive boot disk creation tool tutorial