Nokia mobile code

 

Nokia mobile phone cheats (Code Daquan)
I. * #06 #: display the IMEI code

Ii. * #0000 #: display the software version
(If some models do not work, you can press * # Model Code #, for example, * #6110 #)
Line 1-software version;
Line 2-Software Release Date;
Row 3-Mobile Phone Model

3.*#92702689 #: display the XXX and IMEI codes with a scroll menu
On the first screen, the mobile phone factory time is: 1197 (Months, months, and years );
The second screen indicates-string number and IMEI;
The third screen indicates-the purchase time can be changed once: 1197 (month-year)
(However, once entered, no changes can be made and the date will be recorded permanently)
The fourth screen indicates the last repair time: 0000 (month-year.
The fifth screen indicates-transfer user data: exit and close the phone number, and then return.
If the above is not working properly and you are required to enter a valid code by phone, try:
1). 6232 (OK): displays the month and year of manufacture.
2). 7832 (OK): displays the month and year of the mobile phone purchase time
3). 7332 (OK): displays the month and year of the last service time: 0000 (month/year ).
4). 9268 (OK): displays the serial number.
5). 37832 (OK): Set the month and year of the purchase time (warning: only once allowed)
6). 87267 (OK): Confirm transfer, related to software updates

Iv. rate encoding
* 3370 # Or * EFR #: Enable (EFR) full rate encoding
#3370 # Or # EFR #: Disable full rate encoding
(Enable full-speed enhanced encoding mode to improve voice quality but consume power)
* 4720 # Or * hra0 #: Enable (HR) Half-rate encoding
#4720 # Or # hra0 #: Disable the half rate encoding
(The voice quality is reduced, but the battery usage time can be prolonged by about 30%, which requires Network Support)
After you type the code, it will shut down and re-opened before it takes effect.

V. SIM card lock Information
* #746025625 # (= * # sim0clock #): If the SIM card can be locked, enter this command during detection, the phone displays "Sim Clock Stop allowed" or "Sim clock stop not allowed", depending on your SIM card.
SIM card lock information: includes four different locks
1). National lock-lock specified country
2). Network lock-lock the specified network
3). Supplier lock-lock service provider
4). SIM card lock-lock the specified SIM card

6. Check whether the phone is locked
First, you must find the keys required for setting the mobile phone. "" Appears when you press the * key twice in a row. "P" appears when you press the * key three times in a row. W is displayed when you press the * Key four times in a row ". Then, you can enter the corresponding keys in sequence.
# PW 1234567890 1 #: Check whether the country code is locked
# PW 1234567890 2 #: query whether the network code is locked
# PW 1234567890 3 #: Check whether the network provider is locked
# PW 1234567890 4 #: Check whether the SIM card is locked

VII. Power buttons
By tapping the power key, the screen will display the context menu. You can quickly switch between modes by pressing the up/down key. When you turn on the screen light in the keyboard lock mode, have you ever experienced the headache of hacking at night and trying to turn on the keyboard lock of your mobile phone? In fact, you can tap the power key, then the screen and keyboard night light will open, so that you can easily distinguish the key to open the keyboard lock.

8. view the mobile phone status
Operation Command: # Pw (mastercode) x #
(Mastercode) is a 10-digit (no parentheses) X is a number ranging from 1 to 4. It shows the above locks and is not sure about the number of corresponding locks.
The SIM card does not limit information, which means your phone is not locked.
1). Vin charger input voltage 8.4 v 0.8a
2). chrg CTRL charger control PWM 32 kHz
3). xmic input 60 mV-1 V
4). sgnd signal ground
5). xear ear output 80 mV-1 V
6). MB 9600 B/S
7). fbus_rx 9.6-230.4 kb/s
8). fbus_tx 9.6-230.4 kb/s
9). l_gnd charger/logic Gnd

IX. Nokia 9000/9000 I
1). display the IMEI number: * #06 #
2). display the software version number: * #682371158412125 # the latest version is under the phone number.
3). Display manufacturing weeks and years: * #3283 #
4). Telephone type: ge8

10. Decode locks
Operation Procedure: Press C, and then click-> press C to not put-> press * not to put->
Type 04 * pin.

11. Change the current number
Hold down # The key for about one second, and the screen will show "Switch number ?" After you press confirm, there will be a 2-character above the screen. At this time, the phone cannot dial out but can answer the call. Cancel the re-operation once and use it to lock the machine. When you do not call a call, you can enter the call menu by pressing the function key for two seconds. This menu appears only when you call a call.

12. 6110 display the name on the standby Screen
Choose the most uncommon operating mode, usually the pager Menu3-5, After configuring the personalized selection Menu3-5-2, rename the Menu3-5-3 as your own name, and then start. Note: To recover to a pager, rename the Menu3-5-3 to blank

Nokia mobile phone knowledge (example 8850, similar to others)
Nokia mobile phone knowledge (example 8850, similar to others)
Enter * #06 * string 7 and 8 digits as 10 = Finland 20 = Germany 30 = Korea 40 = Beijing 60 = Guangdong Dongguan
At present, N records are mostly produced in Beijing, with 40 7 and 8 bits. The body, packing box, and serial number displayed must be consistent.

Enter "* #06 #" on the Nokia mobile phone to display the phone string number with 15 digits. It is the "ID number" of the mobile phone. The term is the IMEI origin code, it is also called "International Mobile Equipment Identification Code" (for example ):

* ****** XX ******* x
Tac fac snr sp
Tac = approved number (6 digits)
FAC = final assembly code (2 digits)
SNR = serial number (6 bits)
SP = standby (1 bit)

Nokia mobile phone origin code (FAC)
10 Finland
20 Germany
30 South Korea
40 Beijing
60 Dongguan City, Guangdong Province

Enter * #92702689 #
You can call up mobile phone information. The command is not easy to remember. In fact, it refers to "* # war0anty #", that is, the Code warranty is used. We can see that each letter corresponds to the corresponding number on the keyboard, so the command is not all fabricated by mobile phone dealers.
1. Serial (serial number)
2. Made (manufacturing date)
3. Purchasing date (purchase date)
4. recyclred (repair date

Http://bbs.pcpop.com/081221/4728071.html