Wireless network card can not be used to solve the internet

Wireless network card can not be used to solve the internet

1, the wireless card switch is not open, should first open.

2, the local services.msc in the relevant services are not closed.

3, install the wireless network card management software, through the software configuration and wireless routing related settings, all OK.

Install the Intel PROset Wireless when you install the wireless card driver.

You go into the start-program-intel Proset Wireless Try it.

Is the wireless 0 Configuration service running? To determine if the wireless 0 Configuration service is running, follow these steps:

1. Click "Start" and "Run" in turn.

2. In the Open box, type cmd, and then click OK.

3. Type sc query wzcsvc, and then press Enter.

4. If Windows's "0 Configuration" service is running, the "state: # RUNNING" text is displayed.

• To troubleshoot a wireless network connection in Windows XP, follow these steps: 1. 2. Determine if the driver you are using identifies the wireless 0 configuration service for Windows XP. To do this, follow these steps: 1. Click Start, and then click Control Panel.

2., and then click Network and Internet Connections.

3. Click Network Connections.

4. Right-click Wireless network Connection, and then click Properties.

• • • •

If you do not see the wireless network connection icon in the Network Connections folder, or if you cannot view the properties of the wireless network connection icon, there may be a problem with the driver installation. 1. Click Start, right-click My Computer, and then click Manage.

2. Click Device Manager, and then double-click Other devices and locate the wireless network adapter. If you find the adapter in the other Devices folder, the driver is not installed. To resolve this issue, obtain the driver from the device manufacturer and install it.

3. If the adapter is not found in the other Devices folder, look in the network adapters folder.

4. When you locate the wireless network adapter, note the name and model of the adapter. 5. Right-click the wireless network adapter icon, and then click Properties.

6. Verify that the "This device is working properly" message is displayed under "Device status".

7. If the wireless network adapter is not in the Network Connections folder, either the device is not a problem, or the driver may not be installed. In this case, you will not support drivers for the wireless 0 Configuration service under Device status if you are able to view the properties of the wireless network connection icon, however, you do not see the Wireless Network tab, the network adapter driver may not fully support the wireless 0 Configuration service or the wireless 0 configuration The service did not start. You may be able to configure Windows XP to use connections, but the configuration options may vary depending on the network adapter and driver that you are using. To resolve this issue, use the following procedure to try to create a working connection.

1. Verify that the wireless 0 Configuration service is running. To do this, follow these steps: A. Click Start, then run.

B. In the Open box, type cmd, and then click OK.

C. Type sc query wzcsvc, and then press Enter.

D. If Windows's 0 configuration service is running, the "state: # RUNNING" text is displayed.

2. Click Start, click Control Panel, and then click Network Connections.

3. Right-click Wireless network Connection, and then click Properties.

4. Click Configure, and then click the Advanced tab.

5. Configure your wireless network with the available configuration options. The available options and option names may vary depending on the driver manufacturer. The following list describes the basic configuration options under Properties: • Service Set Identifier (SSID): This setting must match the configuration of your wireless access point or router. If you do not have an access point, the value will be the same on all computers in the wireless network.

• Wireless equivalent Protocol (WEP) or encryption

•

• Data rate: Set this option to automatic or one Mbps. • "Power-saving": In order to troubleshoot, please set "power saving" to "off" or "disabled". You can change this setting after the connection is working correctly.

6. After you configure these options, click OK to save your changes.

7. Test to determine if your connection is working. If a red X appears on the connection icon in the Network Connections folder, or if you are unable to connect, continue troubleshooting.

8. Click Start, right-click My Computer, and then click Manage.

9. In Computer Management, double-click Services and applications, and then click Services.

10. Right-click Wireless 0 Configuration, and then click Properties.

11. In the Startup Type box, click to select Disabled, and then click OK.

12. Turn off Computer Management, and then restart the computer.

When you use this configuration, you should be able to connect to a wireless network if the other network configuration is correct. If the wireless network connection icon appears as a working connection in the notification area, the wireless connection should work. To resolve any remaining issues, use the standard TCP/IP network troubleshooting method.

Drivers that support the wireless 0 Configuration service If the Wireless Network tab in the wireless network connection attribute is available, the driver identifies the Windows XP 0 configuration support for the wireless network. To configure Windows XP for your wireless network, follow these steps: 1. Click Start, click Control Panel, and then click Network Connections.

2. Right-click Wireless network Connection, and then click View Available wireless networks.

3. Click the network you want to connect to, and then click Connect. Follow the steps in the wizard to configure your network. If your network is not listed, verify that the access point is powered on and configured, and move the computer and access points closer to each other, and then test again.

4. If your network is still not displayed as an available network, click Advanced to open the wireless network connection properties.

5. On the Wireless Network tab, click Add to manually configure the settings for the network.

After you save these settings, you can use them automatically if the network is available. The settings available include the following settings: • Network Name (SSID): Network Name (SSID) setting typically matches the configuration of your wireless access point or router. If you do not have an access point, the value must be the same on all computers in the wireless network. • Network authentication and Data encryption: The options Here are "public," "Shared," "WPA," and "Wpa-psk." If you use WPA, no additional settings are required. If you use "WPA-PSK", you need a 8-character to 63-character password.

• Key index (Advanced): This is an optional setting that specifies where the key is stored in the following four locations: 0, 1, 2, or 3. • "Automatically provide this key for me": This check box option specifies that the key is provided by the network or stored on the network adapter. You can enable this key only if your network administrator or network adapter document specifies that you are enabling the key. • "This is a computer to computer (special) network and does not use wireless access points." ": This check box option is used to specify computers to the computer network that do not include access points. If this option is not available, on the Wireless Networks tab, click Advanced. In the Advanced dialog box, you can click Select Access point (structure) network to enable special networks. 6. After you save this configuration, repeat this procedure on other computers on the network. 7. After you configure settings on other computers, you should see the network name SSID in the Preferred networks list. If you see a blue circle that indicates that the network has been found, if you see a red X, there may be a problem with the radio signal between workstations on the network, or the configuration may be incorrect. Verify that the settings on the network are correct, and move the computer closer to the access point or router, or to a location closer to the other computers on the wireless network.

After you complete these configuration steps, the wireless connection will be configured correctly.

If you are having trouble trying to connect to the network, double-click the Wireless network connection icon in the Network Connections folder to view the Connection Status window. In the Connection Status window, there is a signal strength table that can be used to verify the signal strength between computers. Strong signal if you are still having problems connecting, but the signal strength is normal, other network configuration issues may be preventing communication. To resolve this issue, use the standard TCP/IP troubleshooting method. Weak signal if you still have problems connecting, and the signal strength is not good, or the signal is not received, try the steps in the driver section of the wireless 0 Configuration service that is not supported. If the method described in this section still does not resolve the issue, contact the manufacturer to determine if the wireless network adapter and access point are working properly.