Implementation of Dual-router connection shared Internet access

Dual-router connection shared Internet connection implementation vro connection environment description to achieve simultaneous Internet access on five computers, there are two routes: TP-LINK 40 m and TP-LINK 402 router connection method www.2cto.com how to connect to make 5 computers at the same time the Internet? How do I set the route entry?
The specific method is as follows: the wan port of the first router is empty. The lan port is used to connect the computer to the lan port of the second router;
The WAN port of the second router is still connected to the Internet, and the LAN port is connected to the computer and the first router. Set network parameters in the second route. Most people use adsl to access the Internet. Simply put, the network cable from the modem is connected to the first vro,
Set the wan. The second router can be used as a computer. If you want to change the IP address,
The default value is 192.168.1.1. Connect the network cables of other computers to the second vro so that they can access the Internet. Router connection step 1) router A's w port is connected to the Internet, and a l port is connected to router B's L port step 2) fixed DHCP of router B to close step 3) the IP address of the LAN of Route B is changed to an IP address in the same address pool of route A. For details, refer to the dual-router connection method ), call the router connected to the computer (2). The following is the same! Set: 1. Set Route 1 to the default value of the factory. Use a dynamic IP address to access the Internet and clone the MAC of a computer to the MODEM. 2. Set Route 2 as the routing method we use at ordinary times. Use PPPoE to access the Internet, enter the bandwidth account and password, and select automatic connection. Connect www.2cto.com: connect all the network cables connected to the computer to vrouters (2), and the WAN ports of vrouters (2) to a short network cable (1)
Vro1 1 ~ 4. Connect a single port (Remember, it is not a WAN port). The connection line can be set to RJ45 standard,
Then use the MODEM with such a network cable and the 1 ~ of router (1 ~ 4. connect any port! Generally, it is best to work together
Turn on the three power supplies together. Sometimes the three power supplies cannot be switched off when they are disconnected. Otherwise, it will be difficult to access the Internet! Use a route to connect to the Internet directly with the MODEM. When the route is running, you can see that the dial-up Internet access is available, but packets are sent,
Few are returned, but they cannot access the Internet. Then, access the Internet through a computer through a route (connect the line of the WAN port to the MODEM)
1 ~ 4. You can use a LAN port to access the Internet. Try adding one more router, which is equal
There is a switch in the middle, but it only carries a route. It clones the MAC address of the NIC of this computer,
At that time, I wanted to see the sky go across the sea? The result is OK! For example, two routers, A and B, A, let them take advantage of the routing function, dial-up Internet access. Therefore, the WAN port of route A must be connected to the MODEM.
Then route B only acts as A hub, and pulls A network cable from the LAN port of route A to connect the LAN port of Route B,
Connect the computer's network cable to the LAN port of Route B, so that route B can access the Internet through router A without any settings,
Routing B only acts as a channel. Step 1: Adsl --- ROTER1 (dial-up) --- Roter2 (dynamic) --- pc. Step 2 suggests Gateway: route 1 uses 10.10.10.111 --- Route 2 uses 10.10.9.111 www.2cto.com. The network Vanguard can only detect the signal of the first route, but cannot detect the second route,
You can. (Remember to have two routers. It is best to open the fire wall to prevent all firewalls under the *** attack,
Prevents unknown packet check and attacks.) The second router (dynamic) has this dynamic IP address in the route, that is, the attempt to automatically obtain the dynamic IP address! Experiment on your own,
Yes! All the routes on the market have this setting! For example, DHCP is basically configured for the ip addresses of common routers and LANs,
Automatically allocate IP addresses. We recommend that you disable DHCP on the lan side of vro1 1 and set the gateway to 10.10.10.111. Set the wan end of vro2 2 to a specified ip address, for example, 10.10.10.112, 10.10.10.111, and 255.255.255.0,
Vro2 2 enable DHCP on the lan, for example, 10.10.9.100 ~ Section 255. On the pc end, you have more than 255 machines (are there so many )?
The mask uses 255.0.0. The ip address can be set from 10.10. (1-254). (1-254). If not,
Use Limit limit 255.0. The ip address ranges from 10.10.9. (1-254 ). This article is from the chinacache