Installation and setting methods for various models of ADSL Routers

Although the installation of various models of ADSL routers is similar, they still have their own characteristics. Today, from the perspective of installing the 831 ADSL Router, you will find that you can understand it as well. Later, we will introduce how to install vrouters of subsequent models.

China Netcom ADSL Router Installation

The whole process of installing the ADSL Router requires the whole process of the Dynamic IP address of China Netcom. Hey, install the router on the external cat. Achieve the whole process of parallel connection between multiple computers. Because I got it, but I couldn't get it online. Maybe something went wrong. People make such mistakes and you will not find it easily. You will only be able to look at it again after you step by step, so now I am a person who will not install it at all. Please teach me how to install a router, thank you very much.

Satisfactory answer: the page address is 192.168.1.1 or 192.168.0.1 (as described below). If the user name and password are admin, try to specify an IP address, the method is as follows: Right-click "network neighbor properties", choose "Network>" manage network connections ", right-click" Local Connection Properties ", and click" internet Protocol (TCP/IP) "and" Point properties "on the General tab, enter 192.168.1.2 in the IP address bar. If you do not need to fill in other fields, click OK. Then you can log on to the settings page to go to the settings page.

In fact, you only need to set the WAN port type to PPPOE, and enter the ADSL account and password to OK. Of course, you need to enable the DHCP service. This is enabled by default, try not to change the cables for other vromodem settings. Do not connect the wide-line cable connected by the MODEM to the WAN port (only one !), A lan port connected to a computer (usually four or more) is used to access the Internet through a dial-up on a vro. After the setting is successful, the computer can access the Internet directly without dialing.

Set 831:
First, we need to refresh the 831 built-in software to 2. Version 79, which can be downloaded at www.zte.com.cn) 831 the IP address of the Ethernet port set at the factory is 192. 168. 1. 1. In order to access 831 via telnet, we should set the address of a computer to 192 first. 168. 1. * Run ping 192.168.1.1 to check whether the access Traffic reaches 831. If no problem persists, run telnet 192.168.1.1 in DOS mode. If you have just installed the software, you have a password, the original factory password is adsl831. Then we have logged on to 831. Its prompt is as follows:

We can use the help command to get a general idea of the commands we can use. I will not talk about it anymore. How to set the mode: the problem is whether you select the bridge mode or the routing mode. If you press enter, the command is used to clear the Setting data. If you make a mistake later, you must call the command again) r1483> home Press enter> next we will make quick settings, and the system will ask you how to connect to the WAN. We will choose pppoe. The system asked the Ethernet Ip address again: we hit 192. 168. 1. 1) then ask the subnet mask: We hit 255. 255. 255. 0 VPI: 8, VCI: 81, Authentication (Authentication method), we play p, and then ask our User name: How much is it, the following two are the same) password: Repeated password:

Now, you can press y to save all the ADSL Router installation settings. The system asked us if we would like to continue the quick setting. We will execute the save command now, or we will work hard on the white. At this time, 831 is started to restart. Then our TELNET connection will naturally be disconnected. After 831 is restarted, we will continue to telnet and use the show command to check the current situation. If there is no problem, we can see the IP address of the pppoe interface. Congratulations! Your 831 has already dial-up Internet access. How many IP addresses do you see ???, You can unplug the power of 831 and then plug it in.

After such a setup, we only need to set it in the TCP/IP settings on the computer.
◆ IP Address: It can be 192. 168. 1. 2 to 192. 168. 1. 254
◆ Subnet mask: 255. 255. 255. 0
◆ Default Gateway: 192. 168. 1. 1
◆ DNS: 202.96.209.5
◆ 202.96.199.20.
◆ Well, your computer can start surfing.

Now let's talk about advanced settings for installing the ADSL Router: Advanced Settings can use dhcp, so that your computer can automatically obtain the ip address. Enable your computer to act as a server, such as opening an ftp server

◆ How to implement dhcp server:
◆ Telnet to 831
◆> Lan
◆> Lan> dhcpserver 192.168.1.2 192.168.1.254
◆> Lan> dhcpserver dns 202.96.209.3 202.96.199.20.
◆> Lan> home
◆> Save
◆ It's over. 831 will automatically restart. Generally, 831 will not dial after restart, so you need to unplug the power supply.

◆ If you have servers in the internal network, such as ftp)
◆ Telnet to 831
◆> Pat
◆> Pat> addpatin pppoe 21/tcp 192.168.1.5
◆ This means 192. 168. 1. 5. Port 21 is available for ftp service on the computer)
◆> Pat> home
◆> Save
◆ Okay, everything is done.
◆ Route settings up to 2110
◆ Run the "adsl configuration program" file,