Uncover the mysteries of the detailed production process of ipcop soft Routing

I believe many people are still familiar with ipcop soft routing, so I have studied the detailed production process of ipcop soft routing. I will share it with you here, hoping it will be useful to you. Ipcop soft routing is a very easy-to-use router software, built-in firewall, low performance requirements for machines, stable operation, so it was praised by the majority of users. Ipcop is an operating system similar to the Linux interface. It has good routing functions and high stability.

Ipcop soft routing is difficult to install for the first time. You can see an image file of Ipcop V1.4 prepared by a netizen for your convenience. You can use this image for installation, you only need to mirror the entire image file to a hard disk.

I. Hardware conditions for using Ipcop V1.4 image files

The hardware configuration for installing Ipcop is not high, but it must ensure that the machine runs stably and cannot crash or restart frequently. Otherwise, the Internet cafe customers will run smoothly. The hardware configuration of Ipcop for the following 100 Internet cafes: CPU: Sai Yang 466 or above memory: 64 MB hard disk: 5 GB, Nic must use Rtl8139 Nic, you can use the preceding vro configuration to configure the number of two vrouters. It supports 120 machines and has been running for more than three months without shutdown. If the number of machines in the internet cafe is large, you can add hardware configuration properly.

Ii. Install Ipcop V1.4 route

Because Ipcop V1.4 is used as an image file, you can use the clone program to recover it to the hard disk.

1. Find A hard disk with Windows 98 installed and name it A, the same below). If there are only three Windows 98 system files, you can. Put the downloaded Ipcop V1.4 image file to hard drive A, and download the clone program of Ghost 8.0 or above on the hard drive.

2. Mount hard disk A to the machine that is preparing to install the ipcop soft route, start it with the operating system of Hard Disk A, enter DOS, and run the clone program, select the Local Disk form Image option to recover the hard Disk from the Image, that is, clone the entire Disk), find the downloaded Image file, and restore it to the hard Disk of the machine that is preparing to install the ipcop soft route. The clone can be completed in about two minutes. After cloning, shut down.

3. Remove hard drive A and check whether the ipcop soft route can be started properly.

3. Set ipcop soft route

After the Ipcop route is started, when the XX Login: interface appears, enter the admin user name and admin password to enter the Ipcop soft routing interface (XX appears based on the name of the soft routing machine ). If it cannot be started after cloning, check whether the hard disk is on the first IDE interface on the motherboard and ensure that the hard disk jumper is the primary hard disk. This article only sets bandwidth for fixed IP addresses. For more information about ADSL settings, see the related options.

1. Enter the setup program: After logging on to the Admin Super User, run setup to enter the Ipcop setting interface. In the ipcop soft route settings, the network adapter is mainly set. Other options do not need to be set.

2. Network Settings: Red + Green Nic settings are included in the NIC settings of the ipcop soft route. Red indicates the NIC that connects to the Internet. Therefore, pay attention when connecting the network cable, do not insert a wrong network cable. Green refers to the network adapter connected to the Intranet. In the Ipcop V1.4 image version, the network adapter must use the network adapter of the Rtl8139 chip. You can specify the network adapter on the Internet. Otherwise, the system cannot run normally. In the installation version of The ipcop soft route, any network adapter can be used in the intranet. Select the "Network Configuration Menu" To Go To The NIC setting options. There are four sub-menus in which all network settings are included.

3. After Entering the "Netword Configuration Menu" setting Menu for "Netword Configuration type", select the first "Netword Configuration type" to enter the NIC type setting, and select the "Green + Red" item, because the Ipcop soft route uses two NICs. After setting, press OK to save the setting, and press Done to save the setting and return to the upper menu.

4. Set Drivers and card assignments to check whether a new Nic is added to the system. This item must be set to ensure the normal operation of the Ipcop system. If both the internal and external NICs use the Rtl8139 Nic, there is a secret. Install a network card. after entering the system and entering this option, the system will prompt which network card is not found during protection. If no Red network card is found, the current network card is Green, connected to the Intranet Nic.

5. Address Settings setting this option is used to set the network Address of the two NICs. After entering the Address Settings setting item, set the addresses of the Red and Green network cards respectively. First, go to the settings option of the Red Nic, which is generally optical fiber. You can use the Tab key to move to the "Static" option. Then fill in the IP address provided by the Telecommunications Department. DHCP Hostname is the host name after the DHCP service is started. You can change it as needed. Set the IP address of the Green NIC based on the actual situation of the Internet cafe.

6. DNS and Gateway Settings

This setting is mainly used to set the DNS server address and gateway address. After entering this option, you can set the gateway and DNS server address of the Red Nic. Enter the DNS server address and gateway address provided by the telecommunications department, and then press OK to save it. After the preceding simple settings, the ipcop soft route can be used.

IV. Other settings of ipcop soft route

1. Hostname: the name of the machine that modifies the Ipcop soft route. You can give the vro a name based on your interests.

2. ISDN Configuration Menu: ISDN settings Menu. In this Menu, you can set some options of ISDN, such as the user name and password of Ppoe dialing. Because ADSL is rarely used for Internet access, this section is not described in detail.

3. Keyboard Mapping settings: Set the Keyboard area options. Similar to the "Keyboard" option in Windows Control Panel, select the "US" American Keyboard.

4. Timezone settings: Time Zone settings. For use in China, select "China/Beijing". If you do not have Beijing, select Hongkong Hong Kong.

V. Management and Maintenance of ipcop soft routes

This version of Ipcop has been optimized in many settings. In daily management, you only need to perform simple maintenance.

1. terminal maintenance: You can perform maintenance and run some commands on the Ipcop soft routing machine. The most basic one. Run the Ping command at the ipcop soft route prompt to check whether the network is connected.

2. Web page management and maintenance: You can use http: // 192.168.0.20.: 81 to manage and maintain some of the soft routes, such as port ing, DHCP server setting, ADSL password setting, Ipcop password modification, and other operations. Since the Web pages of this version have been written into Chinese, I will not talk about it more.