What if the Tp-link router can't connect to the Internet?

Tp-link routers cannot connect to the Internet a workaround

Tp-link wireless router, model "tl-wr841n", can be used yesterday, whether it is wireless or local connection. Today is suddenly unavailable, wireless and local are dead, the display cannot connect to the Internet. Reset key pressed over, reboot, and even restore factory reset. Not yet. Angry half to death. What the hell is going on here? (Also, the wireless router has used the power of the other card, there is damage?) because the lights are still on, so I don't care.

This special dialer, the router is not able to dial.

You can only find out if you have a router for your local cable TV broadband special dial-up program to crack the method.

Tp-link Routing General address is: 192.168.1.1 is TCP/IP 4 address, XP system does not have TCP/IP 6, because it is not used now, you do not have to ignore it.

You can try it or not: (This is the way to refer to someone else).

To provide you with a way to crack the real account, hoping to help you.

Use dedicated dial-up software on your computer to dial once for a successful (Internet access) then in: "My Computer" right "management" to find "Event Viewer" point open Find "system" in the system there is a information source for the "RemoteAccess" Double-click to open the user in the contents of the description below ( That's your real account. Set the account and your original password to the router.

Note It is best to use MAC address cloning in your router to clone your computer's MAC address and restart the router.

Tp-link routers cannot connect to the Internet solution two

1, the first to ensure that the rear of the router and the modem is connected to the Internet, while the computer inserted in Routers 1, 2, 3, 4 of this type of port;

2, then the router and modem all through the power, first check the router on the normal light.

3, keep the line correct but unobstructed, turn on the computer, first to confirm your IP configuration, such as whether normal, in the "Start" select "Run", enter "CMD" after the confirmation, and then enter the interface in the "ipconfig" to see if the local connection IP is 192.168.1.X ( X can be between 2-254), the default gateway is not 192.168.1.1, the subnet mask is 255.255.255.0, if so, in the browser will be able to open the routing configuration page, address bar input: 192.168.1.1

4, if the above step is unable to pass the words will need to configure your IP, the general method is in the Network Neighborhood right click, and then select Properties, in the inside find the word "TCP/IP" in the line to modify the IP, to keep DNS for automatic access. (If it is Vista or WIN7, select the line of IPV4)

5. After entering the routing configuration page, you can go directly to the "network Configuration" of the "Wan Port Settings" (my router is such a name, the different brands are similar), and then in the Internet account and the Internet password to modify the correct line, do not really account and password words can hit the network provider customer Service consulting.

6, if not yet, you can restore the factory set up: In the router's power cord socket next to a small hole, to find a needle or something, the first power off, and then put the needle in to withstand, open the power, and so on three seconds after the release, and then the landing router reset can be. In addition, you need to see whether the IP connected to your computer with the router is in the same network segment as the router.

7, router restore factory settings, on the computer to open IE, in the address bar input: 192.168.1.1 carriage return

8, no longer the beginning of the words-run--cmd--ping 127.0.0.1 look at the network cartoon impassability, to determine the network card no problem, to replace the router, it is best to have neighbors to borrow so 10 minutes, to determine whether your bad.

If it is used without lines, the procedure is the same, the only difference is that there is no need to have a wireless network card with the wireless router connected with the network, other configuration methods are the same.

However, it should be noted that wireless may be encrypted, if you restore the factory settings, this wireless password is naturally no, need to reset, step reference manual can be, no instructions you can contact me directly. If you have this password, you have to make sure that the password that you have stored on your computer that is connected to this line-free configuration is correct. In fact, I helped a lot of the dormitory has not been able to use the Internet, most of this situation, because the wireless password or restore the factory settings, configuration is correct but still can not surf the Internet.

If not, it may be due to the following reasons:

The reason that routers do not go 192.168.1.1 ①:adslmodem the routing function is turned on and the Lanip address is the same as the Lanip address of the router.

Current default Lanip (Gateway) for most wireless routers Is 192.168.1.1, and many manufacturers Adslmodem this value as the default Lanip, so that once the user connects two devices will occur loop, the computer can still get to the IP address from the router, the DOS command line window using the ipconfig command to view the obtained IP information , but cannot ping the wireless router.

Since the vast majority of users use the wireless router before using the computer to dial the Internet directly, Adslmodem Lanip on this time does not have an impact, so users will often suspect that the wireless router fault, is not. Loop occurs, even if the router and Adslmodem disconnect, only to keep the router and computer connection, the computer still can not ping the wireless router, need to restart the router, or even restore the factory value.

The reset process of the wireless router is generally: under the condition of power, press and hold the Reset key (there is a small round hole next to the antenna, which is the reset key) more than 15 seconds, and then the device will be power off restart. After the router is reset, it can only be connected to the computer, no longer connected to the modem. You can then use two DOS commands ipconfig/release and ipconfig/renew to refresh the computer's IP information (WIN98 under Winipcfg). When you get a new IP address, you can use the ping command to check that once you can ping the wireless router, the connection between the computer and the router is normal.

Then start the browser, in the address bar input 192.168.1.1, enter the router's configuration interface, the default entry is the basic Settings page, ADSL home users usually only in this page set up ADSL account and password on the line, for this fault, see the detailed instructions here:. The wireless router eventually has to connect to modem to surf the Internet, and the IP address of the two is still the same, so you must change one of the Lanip. Change the lanip of the wireless router is very simple, after setting the basic Settings page, click on the left side of the function list of LAN IP settings, this will be the router's lanip to 192.168 2.1, the range of address allocation is also changed to 192.168.2.2~192.168.2.100.

When the wireless router update setting is complete, use the Ipconfig/release and ipconfig/renew two DOS commands described earlier to update the IP information of the computer, and if the computer obtains the correct IP (ie 192.168.2.*), the router's settings are in effect. You can now connect it to the Adslmodem. Finally enter the basic Router Settings page, click "Application", the router is dialed.

Similarly, if the router is not connected to Adslmodem, but other devices, as long as the two IP is the same, it will appear above the problem, so it is recommended to set up a wireless router, the first to determine the IP of other devices, if not sure it will not be the WAN port to other devices, only one computer to the LAN port.

The reason for not going to 192.168.1.1 ②: The browser settings enable the proxy server.

In contrast to the first scenario, pinging a router from a computer at this point is a pass, but the Router settings page cannot be reached. If this description, then should first check the browser proxy server settings, are often agents to provoke the trouble: Start the browser to open a Web page, select the Tools menu Internet Options → connection tab Right below the LAN settings, disable the proxy server function.

The reason for not to go 192.168.1.1 ③: The computer has installed many network cards.

In order to set up the management router, some users will install more than one network card in their own computer, if the network card is not used to set improper, will also cause the same consequences, so, in setting up the router, in addition to the network card in use, it is best to disable the other network cards, to complete the router's settings and then enable.