anyconnect vpn configuration

First, install VPN service The code is as follows Copy Code sudo apt-get install pptpd Second, the next configuration pptpd service There are three main configuration files The code is as follows Copy Code /etc/pptpd.conf/etc/ppp/pptpd-options/etc/ppp/chap-secrets Let's change the pptp

This article provides a comprehensive explanation of LAN networking. During VPN networking for small and medium-sized enterprises, we will encounter many setup problems, here we will introduce you to a configuration scheme for setting up a VPN Server in a LAN, which is illustrated in detail throughout the networking process. Next I will use Win2000 on the

-list 110 permit ip 10.0.0.0 0.20.255.255 172.16.0.0 0.0.255.255 HQROUTE (config) # crypto map vpn 1 ipsec-isakmp HQROUTE (config-crypto-map) # set peer 114.115.26.107 HQROUTE (config-crypto-map) # set transform-set vpn1 HQROUTE (config-crypto-map) # match address 110 HQROUTE (config-crypto-map) # exit HQROUTE (config) # crypto isakmp key zhaoyun123 address 220.231.61.165 HQROUTE (config) # crypto ipsec transform-set vpn2 esp-3des (esp-sha-hmac) HQROU

Step 1 of Cisco ASA firewall VPN configuration: Create an address pool. To remotely access the client, you need to assign an IP address during logon. Therefore, we also need to create a DHCP address pool for these clients. However, if you have a DHCP server, you can also use a DHCP server. QUANMA-T (config) # ip local pool vpnpool 192.168.10.100-192.168.10.199 mask 255.255.255.0 Step 2: Create IKE Phase 1.

The VPN configuration of the Cisco router is not important for network security, but also makes the user more convenient during use. In this experiment, we use the Cisco 2600 router and the Cisco router VPN configuration to implement the blue campus. The networks between the first branch and the second branch are inter

Question:Most firewalls or UTM deployment modes include the routing mode, the bridge mode, and the hybrid mode. The core configuration is the write rule, A good rule will greatly improve the security of the internal network. Of course, if UTM is used, other security components may be attached. For example, the most common rule is the AV anti-virus component, IPS components, anti-spam components, and some other components such as

1, create VPNRouting and Remote Access--configure and enable and route remote access--Custom configuration--Select VPN access, NAT, and Basic Firewall. 2,VPN ConfigurationIP Routing (nat/Basic Firewall)--New interface (select Local network card)--select "public interface to connect to the Internet" and choose "Enable NAT (E) on some interfaces--add servers in th

VPN: installation and configuration of PPTP + MySQL + Freeradiux MySQL storage vpn account Freeradiux verify vpn account 1. install ppp2. install pptp configuration file as follows: unzip vimoptions.ppt pdnamepptpdrefuse-paprefuse-chaprefuse-mschaprequire-mschap-v2require-mp

CentOS PPTP VPN Server (32-bit) installation 1. Package Installation The code is as follows Copy Code Yum install-y PPP Iptableswget http://poptop.sourceforge.net/yum/stable/packages/pptpd-1.3.4-2.el6.i686.rpmRPM-IVH pptpd-1.3.4-2.el6.i686.rpm 2. Configuration file2.1 Configuration/ETC/PPP/OPTIONS.PPTPD The cod

Firewall-based Easy VPN configuration process Objective: To enable a client on the remote Internet to access internal resources of the LAN through an encrypted tunnel by making Easy VPN on the gateway ASA firewall device.The following figure shows the experiment topology. R1 is a router inside the lan. C1 connects to the VMnet1 Nic and uses the Windows 7 operatin

order number of IPSec security policies for both devices. 10.IPSEC security Policy applied on the wrong interface Execute commands on ngfw_a and ngfw_b on the display IPSec policy [brief | name Policy-name [seq-number | extend-acl]] to see if IPSec security policy is applied on the correct interface. 11.SA Timeout configured too small If the user disconnects frequently, the reason may be that the IKE SA time-out is configured too small. The IKE SA timeout period defa

The L2TP tunnel (L2TP tunnel) refers to the logical link between the second-tier Tunneling Protocol (L2TP) endpoints: LAC (L2TP access aggregator) and LNS (L2TP network server). When LNS is a server, LAC is the initiator of the tunnel and waits for the new tunnel. Once a tunnel is established, the new communication between this point will be two-way. In order to be useful to the network, high-level protocols such as Point-to-Point Protocol (PPP) are then passed through the L2TP tunnel. Today, j

Tags: keychain requires PPPoE technology HTTP app fixed ENC deny1. networking RequirementsThe MSR V5 Router uses PPPoE dialing method to surf the Internet, IP address is not fixed, the MSR V7 router uses fixed IP address to surf the internet, and two devices use Savage mode to establish IPSec VPN to protect the traffic of intranet exchange.2. Configuration Steps1) MSR V5 router# Configure an Access control

Experimental environment: (1) The company all game servers, only allow an extranet IP to access, need to maintain the server, must first dial to the designated extranet IP. (2) The company and headquarters communications are to take the VPN channel, the company's internal IP and VPN devices are different network segments, need to be under the VPN device to conn

Recently in the company to use the TMG platform in the country to build a number of new VPN servers for staff mobile operators and engineers to carry out some server operation, but how to more humane to let employees and engineers save cumbersome VPN configuration? Idle to ponder, in fact, our operating system itself has provided such a

= 650; "onclick = 'window. open (" http://blog.51cto.com/viewpic.php? Refimg = "+ this. src) 'height = "358" border = "0" src = "http://www.bkjia.com/uploads/allimg/131227/040PSc5-8.jpg" alt = "clip_image018" style = "border: 0px none;" title = "clip_image018"/> Ii. VPN experiment Configuration: 1, Basic configurations of the R1 router: Add the default route to 10.1.1.2 650) this. width = 650; "onclick = '