This article describes how to install Python and OpenCV on Raspberry Pi 2 or Raspberry Pi B +. it is based on the GTK library and uses Python2.7 and OpenCV2.4.X as an example, if you need a friend, refer to my Raspberry
is no way to connect to the router through the terminal. Write a separate article on how to connect to the network to obtain the LAN IP bar.With the hostname, the default username for the Raspberry Pi is raspberry. After filling in the user name, click Connect and enter the password in the pop-up box, pay attention to choose to save the password, so the next tim
PST 2013Sat Mar 9 13:19:07 PST 2013Sat Mar 9 13:19:08 PST 2013
I found that this script occasionally skips 1 second, probably because the date command is not exactly printed every second, so sometimes the output time is not used.
When I run this script, I log on to a Raspberry Pi and enter "sudo reboot" to restart the device. This script is running all the time.
Enable Raspberry Pi camera without Raspi-config
ask:
HiI have installed the latest Ubuntu Mate on my Raspberry Pi2. I wanted to use the Raspberry Pi camera in this operating system. Al
First, pre-preparationReach the goal:Using Rapberry Pi to drive MQ-2 smoke Alarm module, the information is collected and extracted, and then Zabbix monitoring system to collect and process information collected.1. Prepare the Raspberry Pi (
Raspberry Pi 3+ros Kinetic version
Remote PC +ros Indigo version
First turn on the Raspberry Pi camera function
sudo raspi-config
Start Camera function
and restart the Raspberry
/wpa_supplicant/Click the + --and root directory at the bottom of the RE manager. This creates a new label, open the data/misc/wifi/wpa_supplicant.conf file in turn, long press the file to edit the file, copy the following, is the current phone link WiFi, can be identified by the SSID, such as my
network={Ssid= "Tp-link_aaf0"Psd= "Xxxxxxxxx"Key_mgmt=wpa-pskPriority=4}
Priority=4 4 represents a priority, and the higher the value, the higher the priority.Toggle tab to previous/root/e
Urna SemperInstructor ' s NameJune 14, 2014Briefly:Customize the Raspberry Pi to a wireless portable surveillance camera, plug in a USB camera, plug in the USB WiFi, then encode the data of the camera, push the encoded data to the streaming media server, others can watch the
This assumes that you already have the Raspberry Pi 2/b+, and that it is already installed. If not, I suggest you buy one, they are both cheap and fun.
Personally, I'd rather spend a little more money buying from Canakit. Their logistics quickly and reliably, plus their ready-to-go service is also very good.
Okay, let's start OpenCV and Python installation.Step 0
motion #counterlastuploaded =timestamp Motioncounter=0#Otherwise, the hostel is not occupied Else: Motioncounter=0#Check to see if the frames should is displayed to screen ifconf["Show_video"]: #Display the security feedCv2.imshow ("Security Feed", frame) key= Cv2.waitkey (1) 0xFF#if the ' Q ' key is pressed, break from the Lop ifKey = = Ord ("Q"): Break #clear the stream in preparation for the next
() Camera.close () Gpio.output (G PIO. Low) def setup (): Gpio.setmode (GPIO). BOARD) # Numbers GPIOs by physical location Gpio.setup (Gpin, GPIO. # Set Green Led Pin mode to Output Gpio.setup (Rpin, GPIO). # Set Red Led Pin mode to Output Gpio.setup (GPIO). Out) Gpio.setup (Btnpin, GPIO. In, Pull_up_down=gpio. PUD_UP) # Set Btnpin ' s mode is input, and the pull-up-to-level (3.3V) Gpio.add_event_detect (Btnpin, GPIO. BOTH, Callback=detect, bouncetime=200) def Led (x): if x = = 0:gpio.ou
Using OpenCV with the Raspberry Pi camera2015.11.21 created by HuangtaoRaspi-config"Camera" and select "Enable"Install Pi Camera:===================http://www.raspberrypi.org/archives/3890Test Pi
Raspberry pi +opencv read camera
Call the camera on the Raspberry Pi, read each frame in the video stream, and use the canny edge detection to extract the edges in each frame, the final effect is as follows:
ReadVideo.cpp
#inclu
Use Raspberry Pi to build your own web server (2) set up Apache and raspberry apache
1. Obtain the Server IP Address:
1 ifconfig
2. Change the local hosts file
If you want to enter a d
So the combination of keywords (Raspberry Pi mysql) asks Baidu to ask Google. No results. Fencing yourself to it. Check MySQL configuration file/etc/mysql/my.cnf found the following configuration# Instead of skip-networking The default is now-listen only on# localhost which are more compatible and are not less secu Re.bind-address = 127.0.0.1Here on everything clear, probably means that the
). It works well with Raspberry Pi 2, the transmission speed between multiple mobile hard disks is fast.Horizontal comparison
Before Raspberry Pi 2, I used an RTD1186-based HD player. How can I compare
How to run Ubuntu Snappy Core in Raspberry Pi 2
The Internet of Things (IoT) era is approaching. Soon, in a few years, we will ask ourselves how we were able to survive without the Internet of Things, just as we now suspect that there was no mobile phone in the past. Canonical is a fast-growing but open-market competitor of Iot. The company claims to place its be
Raspberry Pi on the Cloud (1): Environment preparationRaspberry Pi on the Cloud (2): Uploading sensor data to AWS IoT and leveraging Kibana for presentation1. Sensor installation and configuration 1.1 DHT22 installationThe DHT22 is a temperature and humidity sensor with 3 pi
The content source of this page is from Internet, which doesn't represent Alibaba Cloud's opinion;
products and services mentioned on that page don't have any relationship with Alibaba Cloud. If the
content of the page makes you feel confusing, please write us an email, we will handle the problem
within 5 days after receiving your email.
If you find any instances of plagiarism from the community, please send an email to:
info-contact@alibabacloud.com
and provide relevant evidence. A staff member will contact you within 5 working days.