Windows VPN Server Configuration graphic tutorial ultra-detailed version

Of course, VPN is far more useful than this, such as game agents. The following describes how to set up a VPN under Windows. Hope to help you.

Preparations: windows firewall (windows firewall/internet connection sharing (ICS) must be stopped (or port 1723 is allowed); remote Registry (remote Registry) must be enabled; server must be enabled; Routing and Remote Access must be enabled. If the server uses a LAN address, Configure port (1723) ing on the egress router.

Configuration process: 1. Start the System Service

By default, the remote Registry and server services are automatically started in the required services, and only the Routing and Remote Access Services are disabled by default, start the corresponding service.

Right-click "my computer"> "manage" on the desktop, for example:

　　

After entering "Computer Management", click "services and applications" on the left-side-> "services", as shown in:

　　

Find "Routing and Remote Access" on the right of the service list, and right-click "properties", as shown in:

　　

Right-click the selected service and select Properties, as shown in:

　　

Change the Service Startup type to automatic, as shown in:

　　

Right-click "Routing and Remote Access" and click "start", as shown in:

　　

After the system service settings are complete, you may not follow this step to access the system service. There are many other methods. In the end, you only need to start the server.

　　

2. VPN service configuration

Right-click "Network neighbors"> "properties" on the desktop to enter "network connection", as shown in:

　　

You will find an additional "incoming connection", right-click and select "attribute", such:

　　

On the "General" tab of "incoming connection properties", select "allow others to establish a dedicated link to my computer in" tunneling "mode over the Internet or other networks (W) "Front check box ,:

　　

Click the "user" tab above and click "New (N)…" below )..." Create and select a user name and password. You can also select an existing user name and password,

　　

　　

On the "network" tab, click "Install (I )..." → Select "protocol" that contains "IPX protocol" and click "OK", as shown in:

　　

　　

Wait a moment and the Protocol will be installed.

　　

If the network of the VPN Server does not enable automatic IP address acquisition (DHCP), you need to configure the IP Range of the incoming connection and double-click "Internet Protocol (TCP/IP )", in the displayed window, select "specify TCP/IP address" and enter the idle address in the same network segment as the VPN Server. We recommend that you set this parameter to double.

　　

　　

3. Client (access end) Configuration

Use Windows XP as an example to describe the client for configuring VPN

Open Network Connection and click Create a new connection under Network task on the left, as shown in:

　　

Click "Next" in the New Connection Wizard, as shown in:

　　

Select "network connected to my workplace" for "network connection type" and click "Next", as shown in

　　

Select "Virtual Private Network Connection" and click "Next", for example:

　　

Enter your "Company Name". You can leave it blank or not (leave it blank: Virtual Private Network), and click "Next"

　　

Enter the IP address or domain name of the VPN Server and click "Next"

　　

On the displayed completion page, click "finish", as shown in figure

　　

The "connection" page is automatically displayed. Enter the "user name" and "password", and click "Connect ",:

　　

For the connection process

　　

　　

　　

After the connection is successful, a connection icon is usually displayed in the lower right corner. If no connection icon is available, the icon is displayed by default.

　　

Double-click the connection icon to view its status.

　　

　　

After the connection is closed, it is displayed in "network connection". For example, double-click it to connect.

　　

In general, the website cannot be used. In special cases, such as playing games and using Unicom lines to play telecommunications servers, it is generally difficult to get stuck. It is said that some of them can go abroad and return to China Telecom, you can find a friend of a telecom line. If you open a VPN, it won't be very difficult.

This completes the setup of the VPN Server. If you cannot access the Internet after the connection, open the virtual network connection (VPN connection) properties-> network-> INTERNET Protocol properties-> advanced-> remove the check box for using the default gateway on the remote network in general.