Others

The script consists of four files: tar. sh-> loop. sh-> loginfo. exp. The script logs on to each vswitch in sequence, runs the "tftp 192.168.36.44 put vrpcfg.zip" command on each vswitch, and renames the saved configuration file to the corresponding

Switch fault types and analysis methods 1. Switch fault classification switch faults can generally be divided into hardware and software faults. The hardware mainly involves power supply, backplane, port, and module faults. Www.2cto.com 1. Check

For example, management interfaces connecting the console to a vswitch through a serial portWww.2cto.com open the Super Terminal on the computer to create a new terminal connection www.2cto.com set interface properties press the Enter key to enter

Configure enable password switch # conf tswitch (config) # enable password XXXXX www.2cto.com configure telnetswitch (config) # line vty 0 4 switch (config-line) # password XXXswitch (config-line) # login configuration snmpswitch (config) #

S5700 switch http service enabled dir www.2cto.com Directory of flash:/Idx Attr Size (Byte) date Time FileName 0-rw-28 Oct 01 2008 00:01:52 private-data.txt 1-rw-1,218 Oct 01 2008 00:15:03 2-rw-1,089,840 Jan 01 1970 00:02:05 S5700SI-V100R005C01SPC10

SAN Switch license activation step 7450-7451 does not support cascade by default, that is, E_Ports, requires activation licenses for fc # Full Fabric (if MES is upgraded, Full Fabric number is fc ), A maximum of 10 Fabric servers are supported. The

The first step in configuring VLAN 1 in an AVAYA_CAJUN vswitch to set a VLAN is to first create a VLAN. In an AVAYA vswitch, you must first create a vlan id and name. In fact, the name is only used to help identify VLANs, the switch identifies

Cause of err-disable on the switch interface and solution if the interface status is err-disable and show interfaces status err-disabled, you can view the cause of err-disable triggering. Several common causes of switch interface err-disable caused

Vtp and layer-3 switching configuration (config) # ip routing enable the routing function (config-if) no switchport configuration routing interface (config-if) ip helper-address DHCP-server DHCP relayVTPServer mode the management of vlan in The vtp

Take notes recorded by yourself during school classes and share them with others.Step 1: Configure and save the vswitch password (console, telnet, plaintext, and ciphertext)Switch # conf tSwitch (config) # enable password cisco1 ----------- set the

Hub, L2 Switch, router, and L3 switch hub: Previously 10 m shared Ethernet dedicated, currently used less, only work in the physical layer, port and host use half duplex communication, generally, no matter whether the physical connection is bus or

Vlan switching technology Vlan is built on a LAN switch and implements division and Management of logical working groups in a software manner. Its Switching technology generally includes port switching, three types of frames exchange and Token

Switch CLI test point space, question mark, TAB, various editing keys, commands are not completed, abbreviations, Case sensitivity, concurrency testing, etc. are not required to be written into the test case, and each command is not required for

The LAN switch has excellent performance. It comes from its unique internal technical structure. Different switching modes or different switching types are also closely related to the internal structure of LAN switches. Therefore, understanding the

Go to the user interface View [SwitchA] user-interface vty 0 4 Set the authentication method to password authentication. [SwitchA-ui-vty0-4] authentication-mode password Set the password for login verification to the plaintext password

You can connect to and configure a Cisco switch through the Console port. With the Cisco Console line, the RJ-45 end to access the Cisco switch Console port, the COM port to access the computer Com1 or Com2 port, you must note that it is to remember

I accidentally forgot the password of the VSS 6 admin user (this proves my carelessness). I Googled and found the following information: The secret is to hack the um. dat file to remove the Admin password From offset 80 the bytes are (all numbers

We all know how to clear the configuration file of the ZTE layer-3 switch. The cisco switch clearing configuration is erase startconfig! Then reload. However, ZXR10 series switches do not have this command. ZXR10 saves the configuration as write,

Openvswitch: configure the acl of Openswitch using the ofctl tool. The command is as follows: add rule add-flow Switch

Our work on information security has recently been suspected of using some tools for network attack access, which indeed affects network security. In order to improve the security of network access, in this case, no other software tools are used to