Others

Configuration of router 1 for RIP Protocol Communication of Huawei router: www.2cto.com interface Eth-Trunk1 # ip address 192.168.1.1 255.255.0interface Ethernet0/0/0 undo shutdown eth-trunk 1 interface Ethernet0/0/1 undo shutdown eth-trunk 1 #

The transmission of Wireless LAN through wireless routers has become a networking method adopted by more and more users. Wireless Network installation is very convenient and does not require rewiring. Therefore, it will not damage the original

Run show running-config at the beginning of the Cisco router to load ios 2600, create a router, right-click the router, select console enter enable enter privileged mode www.2cto.com enter show running-configR3 # show running-configBuilding

The relationship between the vro memory and the route table and the NAT table is mainly the relationship between the routing characteristics and the NAT characteristics and the memory. When the number of route table entries is less than 2000, 32 MB

Since the launch of the Multi-Wan port router for WayOS, it has been well received by customers. WayOS router features three main features: first, stability, vrouters of the same type are incomparable. Second, ease of use. All operations and

Key features: integrates Four 10/100 Mbps Adaptive Fast Ethernet Switching ports with a built-in HSDPA wireless module, or an external USB 3G wireless network adapter, A high-speed connection to www.2cto.com to share a 3G wireless network (VPN). It

The establishment of a neighbor Idle-BGP process between BGP is started or reset. This status is waiting for the start. For example, if a BGP peer is specified, another event is initialized when a TCP connection request is received, when a vro or

Cisco router CDP protocol, Note: cdp is rarely used, and the private protocol for Cisco devices is used. Therefore, you can understand it. But you must know that you may have used this thing for a day. Since Cisco has developed this protocol, it

When a vpn Router is backed up or changed, the email notifies the target vpn Router to switch to the backup line or the gateway corresponding to a route to change, you can notify the changed content by email to improve the simplicity of management.

In recent years, wireless routers have been widely used. The reasons are as follows:1. the wireless router technology (hardware and software) is more mature and cost-effective in the market.2. Broadband is widely used in China, especially in cities

Cisco practice WS-X4232-L3: a small accident a 4006 mount with a WS-X4232-L3 module and the Status of the Management Engine Supervisor II Engine (WS-X4013) turns red, however, it is no problem to observe the offline test of each module during the

Two ce1 links are bundled into a 4 m link. routing can be used for load balancing, for simple static and dynamic operations, you can also buy the second layer of the E1 multipleer, which must be bundled with ppp, the peer routerB can be configured

Nat route address translation nat lo0: 2.2 r1 (R2) s1/0 ---- s2/0 r1 (R1) lo0 1.1 s1/0 -------- s2/0 r3 lo0 3.3 step 1... r1: en config t hostname R2 no ip domain-lookup lin 0 exec-timeout 0 0 logging syn exit int lo 0 ip add 2.2.2.2 255.255.255.255

The Ospf route rerunning to rip Route3 is the self-made system routing protocol ASBR, and route redistribution is performed through Route0. Route0, Route1, and Route2 are the backbone areas area0. network segment Division: route0-route1 172.16.0.0/25

Enhanced Internal Gateway Routing Protocol (OSPF)I. Introduction to KERBEROS:China site. VPN is a private protocol of Cisco. Cisco is the inventor of the agreement and the only vendor with the right to interpret and modify the agreement. Combining

Routing re-release configuration related commands Router> enRouter # confrouting from terminal, memory, or network [terminal]? Enter configuration commands, one per line. end with CNTL/Z. router (config) # host R4R4 (config) # int lo4 %

Build IPSec VPN with two m0n0 serversFinally, I have no time to build an IPSec VPN environment. test the effect of m0n0 for IPSec VPN connection. First, check my environment (no Internet trial, use LAN connection). m0n0 uses the Simplified Chinese

Routeros dual ADSL Load Balancing script [plain] # may/25/2013 09:26:48 by RouterOS 5.20/ip firewall mangle add action = mark-connection chain = input disabled = no in-interface = pppoe-out1 new- connection-mark = wan1_conn passthrough = yes add

IP address routing instance resolution 1. step 1 of IP address search route table) Search for matched host addresses; 2) Search for matched network addresses; 3) search for default table items (the default table item is generally specified as a

Dynamic Routing Protocol (RIP) 1. introduction for Static Routing, route table items are generated by default when the interface is configured (for directly connected interfaces ), and add table items (usually from the system self-pilot program file)