raspberry pi gpio driver

Linux dual-Nic intranet/Internet settings (Raspberry Pi) Raspberry Pi dual-Nic internet/intranet settings, there are the following methods. 1) use a wired network to connect a PC to a gateway. 2) the other is wired to the intranet and wireless to the Internet. Www.2cto.com, even if there are multiple NICs in the config

# Modify the configuration file Raspberry Pi has integrated the I2C driver and only needs to be started. Modify configuration file Sudo nano/etc/modprobe. d/raspi-blacklist.conf ! [Configure] (http://images.cnblogs.com/cnblogs_com/hangxin1940/466697/o_rasp_i2c1.png "comment the third line ")Comment out the third line, CTRL + x save Next, start the I2C modu

Recently in the toss Raspberry Pi, at that time also did not pay attention to, look at the price, bought Mercury network MW150US Ultra-small 150M wireless USB card. But the tragedy was to use iwconfig and not recognize the wireless card But with lsusb words can see MW150US with is Rtl8188eu chip, search on the network, finally found a solution 1. first download the latest Linux kernel for compiling and inst

1, install the required packagesudo apt-get install Hostpad UHDCPD2. Configuring the/etc/network/interfaces FileConfigure Wlan0 as static addressThe format is as follows:Iface wlan0 inet StaticAddress 192.168.10.1Netmask 255.255.255.0Save, exit3. Configuring the/etc/udhcpd.conf FileSet up automatic assignment of address ranges for DNS gateways, etc.Specific as follows: (according to individual needs to configure)Start 192.168.10.2 # This is the range of IPs that the Hostspot would give to client

This blog will show you how to install three different text-based Web browsers on Raspberry Pi. The original article can be found here or at the bottom of this article. Most Web browsers run a little hard on the small school, or consume a lot of resources, so an alternative solution is to use a web browser based on command line. So far, text-based browsers have not been able to do anything that a common bro

Touch screen buy back for a long time no use, recently found that he is can touch. Tinker a bit.The personal use of Raspberry Pi is the official recommendation system, the version isThe best part of this version is that the kernel has compiled the Egalax touchscreen, and the Apt-get upgrade updates the system to use the touchscreen recently.Calibration of the touch screen is possible, the calibration tool x

Linux-Raspberry Pi system partition There are two main partition commands: fdisk and parted.Both commands require the root permission,First, we will introduce the fdisk command: Fdisk allows you to view the usage of the current file system. fdisk -l Because I installed the system on the SD card, the partition starts with/dev/mmcblk0. We can see that there are currently three actual partitions (/dev/mmcblk

that the appropriate content is modified according to the actual situation: [Unit] Description=wireless Static IP Connectivity Wants=network.target Before=network.target [Service] Type=oneshot Remainafterexit=yes Environmentfile=/etc/conf.d/wifi EXECSTART=/SBIN/IP Link Set Dev wlan0 up EXECSTART=/SBIN/IP addr Add 192.168.34.1/24 broadcast 192.168.34.255 Dev Wlan0 EXECSTOP=/SBIN/IP addr Flush Dev Wlan0 EXECSTOP=/SBIN/IP Link Set Dev

1. Identify the internet cardWith the command LSUSB, you can continue down if you can identify it.2. Install the NIC driverThe Internet card will usually have 2 functions, one is a virtual CD-ROM, used to install the driver, and the other is a network connection modem.Under Linux, it is necessary to install the Usb-modeswitch driver to correctly identify and start the modem function of the NIC.sudo apt-get