Current statusThe default user name in OpenWrt is root, but the default is no password, so SSH does not open by default, but Telnet is used without password, when the root password is set, SSH is turned on, Telnet is closed. And the convenience of SSH is greater than telnet,telnet in the production and testing of the case to be used, so there is no way to let the two coexist.
Step OneModify the Telnet self-boot script to remove password and SSH-relat
Ubus provides a common framework for interprocess communication in the development of OPENWRT platforms. It makes the implementation of interprocess communication very simple, and ubus is highly portable and can be easily ported to other Linux platforms. This paper describes the implementation principle and the whole framework of Ubus.
Ubus source code can be obtained through Git library git://nbd.name/luci2/ubus.git, its dependent Ubox library's g
Make v=99 hint when compiling openwrt source code
Generating index for package./UCI_2014-04-11.1-1_RAMIPS_24KEC.IPKGenerating index for package./WPAD-MINI_2014-10-25-1_RAMIPS_24KEC.IPKSigning key has not been configured
Because of the increased package signature, you can see a description of the added feature in the links below.
https://dev.openwrt.org/changeset/38284
That's what it says. Add package signing key and certificate configuration opt
OpenWrt The system starts, run the/etc/preinit script first to Newifi y1s for example, and then swipe in the Pandorabox firmware
#!/bin/sh # Copyright (c) 2006 Openwrt.org # Copyright (c) Vertical Communications [-z] $P Reinit "] exec/sbin/init export path=/bin:/sbin:/usr/bin:/usr/sbin pi_ifname= pi_ip=192.168.1.1 Pi_broadcas t=192.168.1.255 pi_netmask=255.255.255.0 fs_failsafe_ifname= fs_failsafe_ip=192.168.1.1 fs_failsafe_broadcast= 192.168.1.25
TFTP tool and OpenWrt firmware see download address
Prepare the TFTP environment on the computer and start the TFTPD
Name the compiled ROM Recovery.bin, and put it in the directory where TFTP resides
Connecting the pole-routed LAN port to the computer network port with a network cable
Set the computer's network interface IP to 192.168.1.88/255.255.255.0
Use a sharp object to hold the pole route RESET, to power the pole route
Wait for the TFTPD o
Do not operate on your original phpMyAdmin folder ~ ~ ~ To copy a new operation, so that we can use both local and remote?First, download phpMyAdmin to localI am using the integrated wamp software under Windows PhpstudySecond, modify the config.default.php file under the Libraries folder1, find $cfg[' Pmaabsoluteuri '], set its value to your local phpMyAdmin path, for example $cfg[' pmaabsoluteuri '] = ' http://localhost:9096/192.168.2.1/ ‘;2. Find $cfg[' Servers ' [$i] [' Host '] and set its va
"Reprint Please specify Source: Changuo column http://blog.csdn.net/qianguozheng/article/details/37666829"causesIn order to solve the customer reflects the OPENWRT system on the problem of the network, we have Remote Assistance, we found that IP can access, but the domain name cannot access, which helps us locate the problem---DNS.Online SearchFound a have the same problem, that is the domain name server can not be used, the same is 20M fiber dialing,
When compiling OpenWrt source code, make V=s prompts OpenWrt to appear signing key has not been solution
The compilation appears as follows:
Generating index for package./UHTTPD_2014-10-27-FD8E5E379C23C5FBCEC3E76894B839233DF09067_RAMIPS_24KEC.IPK
Generating index for package./WATCHDOG_1_RAMIPS_24KEC.IPK
Generating index for package./WIRELESS-TOOLS_29-5_RAMIPS_24KEC.IPK
Signing key has not been configured
B
functions called in main.
Early ()In luci2/procd/initd/early. C, we can see that it prints a message: "console is alive ". This information can be clearly seen in the startup print information. What it does in the background also includes (these are completed before printing the console is alive ):
1. Mount proc, sysfs, and tmpfs.
2. Add the device/dev/null.
3. set stdin, stdout, and stderr to the specified device, such as "/dev/console". If no device is specified, it is set to/dev/NUL, is thro
Add usb driver and related scripts to OpenWrtStep 1: Add Kernel support
Openwrt compilation supports the USB automatic mount FunctionMake menuconfig
1) Add USB support
Kernel modules-> USB Support-> Kernel modules-> USB Support-> Kernel modules-> USB Support-> Kernel modules-> USB Support-> Kernel modules-> USB Support-> Kernel modules-> USB Support->
2) Add SCSI support
Kernel modules-> Block Devices->
3) add USB mounting
Base system->
4). Add an
SNMP functions are not discussed, mainly to implement equipment monitoring.Installation of SNMP on the OpenWrt network is also a lot of the introduction of monitoring, but only through the Snmpwalk command to obtain the status of other devices are not introduced.Take a look at OpenWrt's wiki and find the installation method.The key is one sentenceInstall snmp-utilsThe status of the remote device can be tested after successful installation192.168. 1.1O
], PFRAMELXD->HDR.ADDR2);global_addrlocalnum++;if (flag){COPY_MAC_ADDR (Global_addrlocal[global_addrlocalnum], PFRAMELXD->HDR.ADDR2);global_addrlocalnum++;}}Proc section:The application layer writes "s" to the proc node, informing the driver that it needs to obtain the data of the STA, and the driver gives the captured maclist.static struct Proc_dir_entry *entry_wl_beacon_mac;UCHAR global_addrlocalnum = 0;UCHAR Global_addrlocal[max_mcast_list_size][6];static char *maclistbuffer;static int maclis
Make command Simple descriptionMake v=99v=99 indicates output verbose debug informationMake WorldRepresents compiling allMake j=2 v=99As Multicore CPUs, the plus j=2 option can theoretically speed up compilationMake-j 2 v=99 to speed up compilation (deprecated)Clear only one moduleMake Package/qos/cleanCompile only one moduleMake Package/qos/cleanMake Package/qos/compileMake Package/qos/installMake v=99 | Tee Compile_v1.0.0.logThe Hybrid Tee command places the compilation information in the Comp
1: Enter the Trunk/package directory2: New makefile and SRC directoriesNote: The makefile here is for OpenWrt read, src directory is the source of the directory and source code makefile storage Directory3: Enter SRC directory, create new source file and makefile, save exit4: Go back to trunk directory to execute Make/package/helloworld/prepareMake meunconfig--> Select Helloworld--> Save exitMake Package/helloworld/compileMake package/helloworld/instal
Refer to the steps as Link: http://www.right.com.cn/forum/forum.php?mod=viewthreadtid=124604A check failure occurred during make menuconfig, and there are several packages:Libncurses5-dev, Zlib1g-dev, gawk and so on. Probably as a hint.Should be a version of the problem, need is 5.9-4 but installed is a high version of 5.9-10, search on the internet, said to have modified the source, I did modify the source, that is because the source of the official website is too slow, when I follow what they
1. Install CentOS 6.0 in VMware and install it minimal desktop2. Compile firmware and SDK with reference to HTTP://WIKI.WRTNODE.COM/INDEX.PHP?TITLE=COMPILING_WRTNODE_STATIC_SDK/ZH-CNChoose Fedora 17 To install the required packagesYum install-y subversion binutils bzip2 gcc gcc-c++ gawk gettext Flex Libz-dev Flex ncurses-devel zlib-devel make patch U Nzip Perl-extutils-makemaker3. Develop HelloWorld program with reference to HTTP://WIKI.WRTNODE.COM/INDEX.PHP?TITLE=OPENWRT_DEVELOPMENT/ZH-CNTo thi
set of messages that identify a particular component. Such a special set of messages usually expresses some additional information. The information for the component should be described in detail, as some component information will be sent to other components as messages. For example, the ' Qtdemux ' QuickTime rectifier (demuxer) should store the ' redirect ' information in the component information in order to send the ' redirect ' component information in a particular case. 7) application-spe
The content source of this page is from Internet, which doesn't represent Alibaba Cloud's opinion;
products and services mentioned on that page don't have any relationship with Alibaba Cloud. If the
content of the page makes you feel confusing, please write us an email, we will handle the problem
within 5 days after receiving your email.
If you find any instances of plagiarism from the community, please send an email to:
info-contact@alibabacloud.com
and provide relevant evidence. A staff member will contact you within 5 working days.