router openwrt

Http://wiki.openwrt.org/toh/tp-link/tl-wr1043ndOEM mass flashing Flashing hundreds of devices using the web interface can be a real pain. You can use this shell script to automate it: #!/bin/bash# Pass the firmware image file to be flashed as the first and only# command line argument.## The second curl call will time out, but it is expected. Once the# script exits, you can unplug the ethernet cable and proceed to the# next router, but do KEEP each

Tags: Cross compilation openwrt x86 MySQL CMake1. Build a cross-compilation environmentFirst, build a cross-compilation environment on your own machine. I'm using the Ubuntu14.04 x86_64,gcc-4.8.3. If you want to set up a very complete cross-compilation environment, you need to install OPENWRT buildroot environment, operation steps:Http://wiki.openwrt.org/doc/howto/buildroot.exigence,Note that after make Men

Openwrt is used for recent work tasks. I have never been familiar with openwrt before. First, we need to build an environment, and I don't want to buy a Development Board. Therefore, creating a virtual environment is the best choice. [Software environment] Virtual Machine: virtualbox Openwrt: http://backfire.openwrt.org/10.03/x86/

This article has been published by the author Wu Zhiqiang to authorize the Netease cloud community. Welcome to the Netease cloud community to learn more about the operation experience of Netease technology products. This article takes the WFD program as an example:1. fl gdbserver to the router firmware On the host side, use make menuconfig to select the following two items. 1) Advanced Configuration Options (for developers) → toolchain options → buil

http://jasonschaefer.com/openwrt-access-point-only-config/ Http://www.tuicool.com/articles/bEbYV3 Principle Http://wiki.openwrt.org/doc/networking/network.interfaces Http://www.tuicool.com/articles/QZfyQn http://fuyufu.blog.51cto.com/4425673/1150253 http://fuyufu.blog.51cto.com/4425673/1150255 Http://www.openwrt.org.cn/bbs/forum.php?mod=viewthreadtid=4020extra=page%3D4 Goal: Use 2870 to do clent connection network, built-in Wlan0 do ap+ local et

Add n2n to OpenWrt routing, and add n2n service in Ubuntu to enable networking and mutual exchange of 1, OPENWRT hardware environment:To brush their own wr703n into the openwrt (here need to modify the flash chip, change a 8M flash);After the brush machine, install OPENWRT, this tutorial online a lot of, no need to exp

My OpenWrt Study notes (18): Linux easy to develop command aliasLearning Linux commands is the basis of Linux, I believe many people n years ago know this command, learning the amount of time also used it, but over the course of this command will fade out of our vision! In the actual work sometimes forget it, the main reason is that the use of the actual application of the word is not enough!Linux command: alias function Description: Sets the alias of

Compile error: make[3]:enteringdirectory '/home/hevake_lcj/workspace/openwrt/trunk/package/network/config/ Netifd ' mkdir-p/home/hevake_lcj/workspace/openwrt/trunk/dlecho ' Checkingoutfiles fromthegitrepository ... "; mkdir-p/home/hevake_lcj/workspace/openwrt/. trunk/tmp/dlcd/home/hevake_lcj/workspace/openwrt/trunk/tmp

Based on backfire10.03 (http://downloads.openwrt.org/backfire/10.03/from the bottom of the source package backfire_10.03_ SOURCE.TAR.BZ2, later confirmed that it should not be downloaded from here, but should be downloaded from SVN, compiled for h618b version-brcm53xx; the process is recorded as follows:The 1.SDK comes with the Luci version of 0.9.0, resulting in a compile Luci error:/home/hadoop/openwrt/backfire_10.03/build_dir/target-mipsel_uclibc-0

This name is a bit too X-loaded.In fact, the problem is very simple, in general, OpenWrt run on some embedded platforms or routers, and this platform often does not have too many resources, such as hard disk storage. However, some data, such as traffic can only be captured temporarily deposited on it, the accumulation of time, if not to copy the data back and delete the OpenWrt on, it will cause insufficien

Due to the needs of the project, the need to openwrt on the Ubus library to arm, Ubus is used for OPENWRT internal module communication between the library, similar to D-bus, but it is a lite version, specific to the OPENWRT official online to understand. Host for Ubuntu 10.04 cross-compiler toolchain version ARM-LINUX-GCC 4.5.1, Target machine for s3c6410/s5pv2

OpenWrt Source Code compilation operation The first step, download the source package and unzip, the source code is as follows: mtk-openwrt-3.10.14-proc.tar.gz Step two, unzip the source package Tar zxvf mtk-openwrt-3.10.14-proc.tar.gz Step three, set the environment variable Source/etc/profile Fourth step, start compiling Make-j 3 v=99 2>1 |tee build.log|grep-i