softphone dialer

We have explained the PPPoE settings in the previous article. Here we will focus on the configuration of ADSL PPPoA. There are a total of five steps. I believe you can have a detailed understanding of this process after reading the article. ADSL PPPoA configuration environment: LAN ----- (e0) rom0 (atm0) ----- ISP communication line, which must be configured with an ADSL card. ADSL PPPoA configuration 1. Configure the ATM interface The Router (config) # interface atm 0/0 Router (config) #

, error)//This function is similar to the dial function, but one more time-out setting timeout, which contains the domain name resolution if required Func fileconn (f *os. File) (c Conn, err Error)//fileconn Returns a copy of the network connection to file F, and when the call is complete, the user needs to close the file F itself, because it is a copy relationship, so closing C and closing F do not affect each other. The Func Pipe (Conn, Conn)//pipe creates a synchronous full-duplex network c

Seventh: Configure the default routeIP Route 0.0.0.0 0.0.0.0 Dialer1 2, Cisco router connection ADSL WIC card of PPPoE configuration solution: !VPDN EnableNo VPDN logging !Vpdn-group PPPoE Request-dialinProtocol PPPoE !Interface FastEthernet0 IP address 192.168.0.1 255.255.255.0IP nat inside !Interface atm0/0 No IP address No ATM ilmi-keepaliveBundle-enableDSL Operating-mode AutoHold-queue 224 inInterface atm0/0.1 Point-to-Point PVC 8/81 Pppoe-client Dial-pool-number 1 !Interface Dialer1 IP M

) # ^ zConfigurationNovell IPX Routing Protocol: Novell RIP is updated once every 60 secondsRouter (config) # ipx routing [node address]Router (config) # ipx maximum-paths Paths Router (config) # interface Type PortRouter (config-if) # ipx network Network-Number [encapsulation-type] [secondary] Router (config-if) # ^ zConfigurationDDR:Router (config) # dialer-list Group-Number protocol Protocol-Type permit [list ACL-Number]Router (config) # interface

broadcast 　　 Creates a frame relay ing. ABCD is the IP address of the other party, XXXX is the local DLCI number, and broadcast allows the broadcast to forward or update the route. 　　 # No shutdown # Exit 3. Configure the Frame Relay subinterface # Conf t # Int s0.1 point-to-point Corresponding to S0 sub-interface 1, point-to-point mode. # Ip addr ABCD XXXX ABCD is the IP address of sub-Port 1, and XXXX is the subnet mask. # Frame-relay interface-dlci 100 br 4. Configure dial-up backup (1) conf

passwordcipher password ipaddressppp-negotiatetcpmss1024dialeruser account dialer-group1dialerbundle1 1.3 dial 2 Settings InterfaceDialer2natoutbound3002link-protocolppppppchapuser account pppchappasswordcipher password ppppaplocal-user Account passwordcipher password ipaddressppp-negotiatetcpmss1024dialeruser account dialer-group2dialerbundle2 1.4 configure ACL aclnumber3001rule0permitipaclnumber3002rul

backup Main Port # Conf t# Int s0 // S0 is the main port.# Backup int asy 1 // A1 port is the backup port.# Backup delay 0 1 // The delay is 1 second. · Configure virtual Interfaces # Conf t# Ip addr abcd xxxx // "ABCD" is the virtual interface ip address, and "XXXX" is the subnet mask.# Encap ppp# Dialer in-band // activate the call-in function.# Dialer idle-timeout 7200#

Application description:A VPN is established between the branch AR1830) and the Headquarters R3640) through IPSec. In actual environments, AR18xx uses the PPPoE-Client dialing method to access the Internet, its Dialer port dynamically obtains the IP address from the PPPoE Server,This determines that the IPSec VPN between the PPPoE Client Branch and the headquarters has a fixed public IP address) can only be automatically negotiated by IKE. At the same

, nil} The DIALTCP () function receives three parameters: Network: This parameter, like the network parameter of the RESOLVETCPADDR, must be a TCP net name. A pointer to the LADDR:TCPADDR type that represents the local TCP address. A pointer to a RADDR:TCPADDR type that represents a remote TCP address. It will connect to dial two TCP addresses and return this connection as net. The Tcpconn object returns (connection failure returns error). If we do not need to have too much contr

Link: http://www.doriandeng.cn/archives/97.html Unity initialization mainly registers the type ing and specifies its lifecycle. In this article, we use an idialer interface, an abstract base class dialer that implements the interface, and two concrete classes inherited from dialer, buttontypedialer and figureplatedialer, and a telephone class that uses dialer