Others

Solve the problem caused by multi-point bidirectional route redistribution (route pruning) first look at which scenarios will use the two-way route redistribution scenario 1: The company has two technical directors, respectively managing the

The Tenda routing Bridge Function introduces how to set the Bridge of the Tenda router. Before setting the bridge, we must set the wireless encryption of the router.1. log onto the tengda vro interface and click the Advanced Settings button in the

The H3C terminal Console analyzes the so-called terminal Console. It simulates the terminal into the router and configures the router. 1. The steps are as follows: www.2cto.com Router # configure terminal (entering configuration mode) Router # line

Many netizens have encountered such a strange problem that the network route is connected to a normal wired network but cannot connect to the wireless network. That is, the LAN port of the wired connection router can access the Internet normally,

In the process of using wireless networks for Belkin route settings, a slight error occurs, which may cause various faults and affect the normal internet access efficiency. The following are several fault examples, to describe the key aspects of

Dynamic Routing Protocol-link status if the distance vector routing protocol is like a road sign, the link status routing protocol is like a map-it owns the entire network. The link status routing protocol is also called the shortest path first or

Show runBuilding configuration... Current configuration: 645 bytes! Version 12.3 service timestamps debug datetime msecservice timestamps log datetime msecno service password-encryption! Www.2cto.com hostname r1! Boot-start-markerboot-end-marker!

RIP and OSPF default route re-release (created in simulator 7200) R1 | RIP | R2 | OSPF | R3R1 # show running-config! Www.2cto.com hostname R1! Interface Loopback0 ip address 10.0.0.1 255.0.0.0! Interface Serial1/1 ip address 255.0.0.1 255.0.0.0

1. Password Recovery preparation A, PCB. ASA configuration line You need to connect the comport of the PC to the control interface of the ASA through the configuration line. 2. Password Recovery ProgramFirst, we open the Super Terminal of the PC,

What is the difference between Bridge, WDS Bridge, and WISP Universal Relay? 1. Bridge and WDS need to set their own routing MAC on the route from the other side. If both routers are their own, this method can be used. If the network is from ceng,

About the AIX Route settings command to view and configure the Route list, for example, the query command is: # netstat-rnRouting tables Destination Gateway Flags Refs Use If PMTU Exp Groups Route Tree for Protocol Family 2 (Internet ): default 10.0.

Introduction to dynamic routing different routing protocols use different measurements. Sometimes multiple measurement hops bandwidth Load Measurement reflects the traffic usage of links along the way. Unlike the number of hops and bandwidth, the

The method for creating an intranet on the lingke router is very common for a home or office. However, many people do not know how to use a vro to build a network, this is what we want to talk about today. Here we take the lingke router as an

Router interface parameters and meanings router # sh int fa0/0 FastEthernet0/0 is up, line protocol is up Hardware is MV96340 Ethernet, address is 0021. d800.0000 (bia 0021. d800.0000) Description: Internet address is 1.1.1.1/30 MTU 1500 bytes, BW 10

Use NetStat-r to query and analyze the route table to view the current system route table. The information provided in this table is: 1, and the LAN is 192. 168. 203 IP segment, your IP address is 128, and the gateway is set to 2. If the network you

Test principle of the OSPF router interface Startup Process: The OPSF interface is in the DOWN state and does not exchange information with any neighbors. INIT status: Send the HELLO packet (type 1) TWO-WAY bidirectional status every 10 seconds:

The establishment of TP-link routing wireless network technology has been constantly in-depth into our daily life, basically every family has set up a wireless network, this article takes TP-link router as an example, I would like to introduce some

The rational configuration of the Alpha routing protocol network has penetrated into our daily lives. How to ensure the stability and transmission speed of the network is the top priority. This requires a good router, in the process of configuring a

In a multi-protocol network with an odd or even number of routes, the customer Address Allocation is very fine, many of which are: www.2cto.com 192.168.1.0/24192.168.2.0/24192.168.3.0/24192.168.4.0/24192.168.5.0/24 .......................... Some

The ACL Access Control List (ACL) is the command List of the vro and vswitch interfaces. It is used to Control incoming and outgoing packets on the port. A table contains matching relationships, conditions, and query statements. It is a framework