broken pipe

When writing a socket program in Linux, if you try to send it to a disconnected socket, the underlying layer will throw a sigpipe signal. After the client sends a message to the server through pipe, it closes the client. At this time, the server generates a broken pipe signal when it returns the message to the client. For signal generation, we can use the method

?In fact, there are problems, a period of time to find a continuous scan after about more than 20 minutes, the connection was disconnected, but also a difficult search, found to be hbase This version of the problem, it will all the connection (whether or not in use) default to idle state, and then have a hbase.thrift.connection.max-idletime configuration, So I'll configure this as 31104000 (one year), if it's in CDH, it should be in the Admin page configuration,General steps to encounter problem

server and the database server are AIX.2. Detect the connectivity between the application server and the database server, ping the database server on the application server ip,ping a minute, is a pass, and there is no problem of packet loss. Telnet the database server IP: port on the application server, it is pass, connectivity is not a problem.3. Log in to the database server, view the listening log listener.log, and found that the application server IP is normal.4. It is still not possible to

Symptoms: Warning:error Sending End PacketJava.net.SocketException:Broken Pipe Information: The cause of broken pipe is usually when the pipe read end is not read, and the end of the pipeline is written, the pipeline is interrupted. (Because the pipe is a one-way communica

SSH "Write failed: Broken pipe" timeout issue fixed, sshpipe Bloggers are keen on a variety of Internet technologies. They are often nagging and often accompanied by obsessive-compulsive disorder and are often updated. If they think that the articles are helpful to you, they can pay attention to me. For more information, see "Deep Blue Sickle" When using ssh, the error message "Write failed:

After debugging for almost one day, I am tossing and killing me for a bug. The reason for the bug is that Code When not careful, will: Written: Obviously, A function starts to call itself recursively without limit.In a short time, the stack of the thread where the function is located will be full, so stackoverflowerror will be thrown.Once java. Lang. stackoverflowerror is found, it indicatesProgramThere is an endless loop in it, or there are too many recursive layers, so all the stacks alloca

When using the socket to simulate the HTTP POST upload data, we encounter the following problems Exception information: 07-31 16:05:49.165:w/system.err (16351): java.net.SocketException:sendto failed:epipe (broken pipe)07-31 16:05:49.165:w/system.err (16351): at Libcore.io.IoBridge.maybeThrowAfterSendto (iobridge.java:499)07-31 16:05:49.165:w/system.err (16351): at Libcore.io.IoBridge.sendto (iobridge.java:

) at Java.lang.Thread.run (thread.java:619)The errors is caused by writing to a connection while the other end has already closed it. Basically, this was caused by the peer unexpectedly ending the connection (for instance, by closing the browser of an H TTP connection). When the user closes the client session, the server cannot write any streams to that client and generates this error. If you click in a link and before the page are rendered you click in a second one. The first request is can

Cocould not create pool connection. The DBMS driver exception was: Io exception: Broken pipe, dbmspipe On-site feedback from colleagues: middleware weblogic cannot connect to the database Oracle. You can see the following in the log:Caused by: weblogic. common. ResourceException: weblogic. common. ResourceException: cocould not create pool connection. The DBMS driver exception was: Io exception:

I wrote a server program. During testing in Linux, I always exit inexplicably. Finally, I tracked the exit caused by a write call. I used GDB to execute the program and prompted "Broken pipe" when exiting ". Finally, the problem is determined that a socket that has been closed on the peer end is called twice for write. The second request will generate a sigpipe signal, which ends the process by default. The

Encounter a very strange problem, web.py code inside the errorIOError: [Errno] Broken pipeStart command: Nohup python xxx.py > Xxx.log SSH log on to the machine, boot, does not appearIOError problem occurs when remote SSH executes the startup scriptView the process PID, LL/PROC/Guess is SSH login in the past, Nohup will redirect stderr, default redirect to stdout, but SSH session stdout should be pipe, beca

In the recent C + + server, when communication between two servers, one is Logserver, one is Gameserver, Gameserver timed to Logserver heartbeat packet (that is, logserver equivalent to the server , gameserver equivalentto the client), suddenly disconnected logserver, the equivalent of a server crash, the client does not know, still send data as usual, but the corresponding connection does not exist, Gameserver will report broken

From http://www.linuxidc.com/Linux/2011-03/33134p2.htm When you write the socket program under Linux, if you try to send it to a disconnected socket, it throws a sigpipe signal to the bottom. When the client side sends the message to the server by pipe, it closes the client side, and when the server ends, the message is returned to the client to produce a broken pipe