nxp development board

Beaglebone Black Development Board installation driverBeaglebone Black Development Board installation driver, before using Beaglebone Black Development Board to do anything before the first need to install the driver. The followin

Environment Monitoring System Based on zigbee and tiny4412 Development Board, zigbeetiny4412 1. Build the Development Board Environment 　　1. layout of tiny4412 linux Reference blog: http://www.cnblogs.com/luoxiang/p/4186391.html 2. boa Server Construction　　 Download boa Source package: http://www.boa.org/boa-0.94.14rc2

, Amy electronics guessed that Altera cut down the low-end fpga I/O diode clamp protection circuit to reduce costs. Recommended plugging Sequence Cabling Sequence 1. Power off the FPGA Development Board; 2. Connect the JTAG cable of the JTAG simulator to the JTAG interface of the FPGA Development Board; 3. Ins

Altera officially has a de2 Development Board, which has rich resources and complete peripherals. It uses ten-layer circuit board design, and the price is naturally high. I made a piece based on the principle diagram, called diy_de2 Development Board. The

Recently, two jz4750 APUs development boards are required for trial. This is also the first contact. I encountered a lot of problems in the middle and finally spent a lot of time doing a good job. Here I will summarize all the process records (for the time being, I cannot upload a picture, and I will try it again if I have a chance ). This diary is divided into the following points: 1. hardware connectivity 2. Linux environment construction and kerne

When using GDB on the Development Board debugging, sometimes need to look at the source code, but the source code is too large, the development Board capacity is limited to pass through the SCP every time the development Board, or

Update Development Board firmware The IDE contains the released board and sub-dedicated firmware. Follow these steps to update your board with IDE:(1) disconnect all power supplies (USB and 5 V power supplies ). Make sure no sketch is running on the board(2) Remove the SD c

Building nfs server fedora13 in the development board environment of s3c6410 and building nfs server in the development board environment of is a revolutionary tool for the development board! With nfs, you don't need to keep your

Iconv_open ("UTF-8", "gb2312") on ARM development board The application code is as follows: Static int code_convert (char * from_charset, char * to_charset, char * inbuf, size_t inlen, char * outbuf, size_t outlen) { Iconv_t CD; Char ** pin = inbuf; Char ** pout = outbuf; Cd = iconv_open (to_charset, from_charset );If (Cd =-1){Perror ("iconv_open :");Return-1;} Memset (outbuf, 0, outlen );If (iconv (Cd,

ArticleDirectory Sorry, it's been too long for everyone to wait. The upgraded black gold Development Board can finally meet you. According to your needs, I have made constant changes to it, so the longer the time is, the more I believe that it is worthwhile to use this time to wait for an upgraded version of the black gold Development

MiS603 Development Team Date: 20150911 Company: Nanjing mi Lian Electronic Technology Co., Ltd. Forum: www.osrc.cn Website: www.milinker.com Shop: http://osrc.taobao.com Eat blog: http://blog.chinaaet.com/whilebreak Blog Park: http://www.cnblogs.com/milinker/ MiS603 Development Board Chapter 11th CY7C68013A Slave FIFO return transmissionCY7C68013A provides a powe

flash device number, you can use the command "NAND device" to view the specific Flash device information on the Development Board. Offset refers to the starting offset address of the kernel file in Flash. It automatically reads the end of the kernel image (processed with mkimage), so no read size is given. Example:Nboot 80700000 0 200000Tftpboot [LOADADDR] [[Host_ip:]filename] uses the TFTP protocol to boo

I. Overview 1. The display drive architecture of flisikar imx6: 2. Objectives: Because the sabrelite Development Board itself has provided LVDS interface, the target screen is LG's LP101WX1-SLN2, its main parameters are: Resolution: 1280*800 Color: 18 digits Color: 262 K Clock frequency: 69.3 M Hz 2. porting process 1. First, connect the screen interface to the LVDS interface of the sabrelite

I wrote an LED driver over the past two days and read many posts online. The idea is very clear at first, that is, first look at the circuit diagram and find that the LED lights are connected to the GPM port, Then, let's look at the data manual, first to gpmcon port write command words, let the GPM0-5 set to output, and then write data to the gpmdat port, in the GPM0-5 pin to pull low or pull high level, To control the LED lighting. 1. Circuit Diagram Obviously, the LED light is connected to th