can terminate this process.
Test the Ethernet Channel Configuration
The next step is to test the Ethernet channel, which is bound with the switch port to provide more Ethernet connections. If one channel fails, the Ethernet channel usually provides redundancy. This process uses the port aggregation protocol PAgP), which takes about 15 seconds.
Trunk configuration test wired and wireless networks
Next, the switch starts to test whether the port is a port that is interconnected between the Trun
wireless routers are the network of this mode.There is an essential difference between a wireless relay router and a common network of home wireless routers. Ordinary wireless routers generally walk on the ADSL PPPoE, which is the wired network. The downside is to share the Internet of wired networks with other devices through wireless hotspots. Wireless relay is different, the uplink of wireless relay is a wireless network, is generally the home of the cat attached to the wireless router to sh
called "Static VLAN", and the latter is naturally "dynamic VLAN".A static VLAN, also known as a port-based VLAN (portbased VLAN). As the name implies, it is the setting that explicitly specifies which VLAN each port belongs to. 、Dynamic VLANs Change the VLAN that the port belongs to at any time, depending on which computer is connected to each port. This avoids actions such as the above change setting. Dynamic VLANs can be broadly divided into 3 categories:L MAC address-based VLAN (macbased VLA
to connect 905b 905c In the lan ?? "
Certificate ----------------------------------------------------------------------------------------------------------------------------------------3Com 905 series IntroductionThe prototype of the 3c905-tx-----------905 series (with unknown functions) I used the original data volume the day before yesterday but it was found to be a prototype... Sent to friends...3c905b-tx ------------ the first shard Store forward function can greatly increase the number of
access time, and so on, which can help companies make decisions on operational strategies.
Security Manager
Web projects run on the Web container platform, which is like embedding an application on a platform to run, so that the embedded program can run properly, first the platform to be safe and normal operation. and to maximize the platform is not affected by embedded applications, the two to a certain extent to achieve the effect of isolation. The policy file is specified by-djava.secu
Compare the OSI seven layer model and the TCP/IP four layer model
The OSI seven-layer model enables reliable communication between different networks of different systems through seven hierarchical structural models, so its main function is to help different types of hosts achieve data transfer.
The nodes that complete the relay function are often referred to as trunking systems. In the OSI seven layer model, the relay systems at different tiers
following example prints the 2nd field of the input record containing ' foo '.Gawk '/foo/{print $} ' bbs-listThe results are as follows:555-1234555-6699555-6480555-2127RegExp can also be used in the comparison equation.(P24 ofExp ~/regexp/If exp conforms to regexp, the result is true (true).Exp!~/regexp/If exp does not conform to regexp, the result is true.5.3 Comparison equations as patterns.The comparison pattern is used to test the relationship between two digits or strings, such as greater
/servers/linux_net.htm#network
P25-8 nmap
Portsentry/snort
-------------
Information Encryption
Plaintext vs ciphertext
Screen Display vs Package content
Http://www.study-area.org/network/network_enscp.htm
Eavesdropping techniques and Prevention
What is the prerequisite for eavesdropping packet?
Eavesdropping tools
Tcpdump
Sniffit
Intercept point routing?
Hub vs Swtich CSMA/CD?
Encryption methods and principles
Encryption Principle
Original Encryption
high Withstand Voltage. Due to the leakage of the original side of the transformer, when the power switch is turned off, the leakage source will generate a large voltage spike, in addition, the input current has a large ripple, so the input filter has a large volume.
Simplified Circuit Diagram of the push-pull part of the transistor
Step 3 call the gpio_init () function to initialize the peripheral gpio. The Code is as follows::
Gpio_init (gpioc, gpio_initstructure );
Step 4. Note: In the F
Hackrf's P20 and P25 are defined, everyone goes to see its hackrf-one-assembly.pdf and hackrf-one-schematic.pdf (HACKRF code base doc/hardware directory). About the pin pin definition of the 1602LCD module, as well as the pin PIN definition of the USB serial port It's a bad street.2 software DemoI gave the HACKRF firmware code loop on the LCD display two lines, but also to the computer minicom print serial output. Baud rate 921600.Core source Files H
The most common project risks in software development are poor requirement analysis and poor project design. A good project planner can eliminate the major risks as early as possible, so that most of the work of the project can be carried out as smoothly as possible, so the preparation work tends to focus on improving demand analysis and project planning. ----------- Chapter 3.1 P25
My opinion: when I saw this passage, I thought of two projects in th
the link delay in NS2. in wide area networks, it is generally in ms. The calculation method is propagation delay = D/S.D is the physical distance between nodes, and s is the propagation rate of the link, which is about 2*10 ^ 8 --- 3*10 ^ 8. It depends on the physical media of the link, for example, S = 2*10 ^ 8D = 100 m, so P-delay = 0.5 us, 0.5 microseconds
For the classification and interpretation of delay, see Computer Network: top-down methods and Internet features
just wants to help sell windows internal.
P17. _ Unicode is really not easy to use.
P21. Memory leakage can also be detected in this way.
P22.windows stability is based on limited tolerance for errors.
How can we leave the dwflags empty after its low-byte padding?
What is the cause of failure? strsafe_e_insufficient_buffer? Isn't that a return value? The target buffer zone is too small!
P23. why is it because strasafe_fill_behind_null is executed and 0xfd is specified?
*) malloc (sizeof (int)); int num = 6; P2 = # int **PTR3 = p2;
Practice:
#include
Reason:
1) Three-province pointers: The type of the pointer p2 is int *, the type of int, the initialization is not pointed, and the pointer is num (note that at this point P2 and num type are int*, you can assign a value)2) Three-province pointers: The type of pointer ptr3 is int * *, the point of type int*, the address of the pointer P2 (note that at this point ptr2 and p2
) Mastering the specific meanings of commands, options, and parameters in the command formatA) command: Tell the Linux (UNIX) operating system what to do (execute).b) Option: Describes how the command runs (you can change the function of the command). The options section starts with a "-" character.c) Parameters: Describes what the command affects (action) (such as a file, a directory, or a paragraph of text)Ls–a/2.whoami commands (see Linux System Management P24)1) Understand the function of th
The content source of this page is from Internet, which doesn't represent Alibaba Cloud's opinion;
products and services mentioned on that page don't have any relationship with Alibaba Cloud. If the
content of the page makes you feel confusing, please write us an email, we will handle the problem
within 5 days after receiving your email.
If you find any instances of plagiarism from the community, please send an email to:
info-contact@alibabacloud.com
and provide relevant evidence. A staff member will contact you within 5 working days.