realtek 5 1 driver

://www.realtek.com.tw/Default.aspx download the corresponding NIC driver.4) Unzip the file using the command: Tar jxvf r8168-8.039.00.tar.bz25) Use the command sudo./autorun.sh installation. At this time,error will occur because we do not have the kernel source package installed, you need to use the method in step 1), 2) to install "Kernel-devel", the command is:Yum--disablerepo=\*--enablerepo=c6-media Inst

... ######################################## ### [100%]1: kernel-devel ##################################### ###### [100%]In this case, check the/usr/src/directory.Now your kernel source code is installed.GCC Section[Root @ localhost 2.6.18-8. el5] # whereis-B gccGcc:/usr/bin/gcc/usr/lib/gcc/usr/libexec/gccIf there is no output, you have to install GCC. Go to [url] http://www.gnu.org/#/url#to download the file.3. Download the NIC

Android Deep Explore ( vol. 1) HAL with Driver Development Learning notes (5)The fifth chapter builds the test environment of the development version of s3c64101. s3c6410 Processor Overview The s3c6410 is a 16/32 -bit RISC microprocessor designed to provide a cost-effective, low-power, high-performance application processor solution, such as mobile phones and g

slot, set the SD card to boot, open the Development Board. Enter the command after the # prompt. Yjsx start copying data from SD card5. Calibration screen: After installing Android, close the Development Board, restore the switch to the Nandflash boot state, calibrate the screenThree. Configure the Wired networkSet the IP and subnet masks using Ifconfig, and set the gateway with the route command.Ifconfig eth0 192.168.17.150 netmask 255.255.255.0 upRoute add default GW 192.168.17.254 dev eth0Ti

Linux Device Driver Article 5: concurrency and final state in the driver, linux Article 5Summary In the previous article, I introduced the debugging method of the linux driver. This article describes the concurrency and status encountered in driver programming and how to han

[Video] Secrets of Embedded Linux/Android driver development (1) Touch Screen driver development and android driver development Secrets of Embedded Linux/Android driver development (1) Touch Screen

adcdat0 register) is read. Otherwise, set the enable_start bit to start A/D.(4) When the conversion ends, read the adcdat0 register to obtain the value. If you use the query method, you can choose not to read the ecflg bit of the adccon register to determine whether the conversion is complete. Otherwise, you can use int_adc to interrupt the conversion. If int_adc is interrupted, the conversion is complete. ADC Driver code: http://www.cnblogs.com/hoys

Drivers The first 5 steps above are the next three steps in how to write a Linux driver to make Linux drivers work correctly. 6.3 First Linux Driver: Count the number of words1. first establish The directory where the Linux driver is stored, and then create the source code file. Finally write a makefile file2. w

Article Title: RouterOS2.8 hardware driver list (1 ). Linux is a technology channel of the IT lab in China. Includes basic categories such as desktop applications, Linux system management, kernel research, embedded systems, and open source. Device Driver List Document revision: 2.8 (Wed Oct 13 11:39:39 GMT 2004) Applies: MikroTik RouterOS

defined in int access_ok(int type, const void *addr, unsigned long size); The first parameter should be verify_read (read) or verify_write (read/write). The ADDR parameter is the user space address, the size is the number of bytes, and sizeof () can be used (). Access_ OK returns a Boolean value: 1 is successful (access is OK) and 0 is failed (access is faulty ). If it returns false, the driver shoul

Linux C programming practice (5 )?? Driver Design 1. introduction the device driver is the interface between the operating system kernel and the Machine hardware. it shields the hardware details for applications. Generally, the Linux device driver must complete the following

MongoDB samus Driver (1), mongodbsamus driver Https://github.com/samus/mongodb-csharp The official driver is not easy, so I used this, 1 var connectionString = new mongoonstringbuilder () 2 {3 ConnectionTimeout = TimeSpan. fromSeconds (30), 4 ConnectionLifetime = TimeSpan

1. Preparations First, install the GCC tool chain and the development environment. You can check the previous steps. You have to compile the kernel. Generally, the Development Board has the kernel. Now I do not know how to configure the kernel. You can only compile the kernel according to the default settings of the Development Board. uboot needs to be compiled before compilation, it is recommended that new users like me learn to write drivers first a

out; and if let the school sister bring over, the computer this one to take a more than one meeting opportunity, in the pursuit of the meaning of many times to meet the students are tacit. Take back the computer of MM and so what, hurriedly to solve the problem of computer-driven! Open Drive Life 5, Drive Life 5 Intelligent Detection system will automatically on the MM computer

Nandflash driver porting series Article Navigation: Nandflash driver porting (1) Nandflash driver porting (2) Nandflash driver porting (III) Nandflash driver porting (4) Nandflash driver