SPI interface
SPI interface IntroductionSPI is a synchronous serial transmission specification released by Motorola. It is often used as a serial expansion interface for MCU peripheral chip. SPI has four pins: SS (from device Selection Line), SDO (serial data output line), SDI (serial data input line), and sck (synchronous serial clock line ).
The Secret mixed-signal Life of PWM PeripheralsPulse-width modulation (PWM) peripherals has enjoyed a long association with microcontrollers and power control, starting With the motor control and power conversion. For the more part, these applications use traditional digital PWM designs, with the PWM peripheral driving
[Allwinner ClassA20 class library Analysis] 5. Use of the PWM class, classa205.pwmThis section describes how to use the PWM class. Download The classa20class library at https://github.com/tjcfeng/classa20.
PWM, another typical output function, is a very effective technology that uses the digital output of the processor to control analog circuits. It mainly inclu
Through the introduction of the previous article, we know that the SPI Universal interface layer is used to connect the specific SPI device protocol driver and SPI Controller driver, the general interface layer in addition to the protocol driver and controller driver to provide a series of standard interface APIs, but also for these interface API defines the corr
Chapter 7 ---- pwm buzzer and ---- pwm buzzer
Linux code reuse:
You can load the header file to use all the original functions. The dynamic mode is that one driver uses the resources of another driver.
For an experiment like a buzzer, there are many internal files, and all the source code must have a lot for proper management.
If there are multiple files, module-y specifies all the files, and then a bui
driver! Similar to the functions implemented by i2c_core.c! It is also very similar to the SPI driver we have previously done! Similar to SPI. C. This file implements the show and store functions, so we can directly use the echo and CAT commands in the terminal to change the backlight brightness!
In fact, the so-called duty cycle adjustment is not as appropriate as the empty proportion, which may have the
IICVsSPIToday, in low-end digital communications applications, we are seen in IIC (inter-integrated circuit) and SPI (Serial peripheral Interface). The reason is that these two communication protocols are ideal for near- low-speed inter-chip communication. Philips (for IIC) and Motorola (for SPI) have developed both standard communication protocols for different backgrounds and market requirements.IIC was d
Through the first article, we already know that the whole SPI drive architecture can be divided into three parts: Protocol driver, general interface layer and controller driver. The controller driver is responsible for the data sending and receiving work at the lowest level, in order to complete the data sending and receiving work, the controller driver needs to complete the following functions:1. Request the necessary hardware resources, such as inte
SPI, is the abbreviation of English serial Peripheral interface, as the name implies is the serial peripheral device interface. SPI, is a high-speed, full-duplex, synchronous communication bus, and on the chip's pin only occupies four lines, saving the chip pin, while the layout of the PCB space saving, convenient, it is for this simple and easy to use features, now more and more chips integrated this commu
called, a set is returned. The second is the software PWM controller we need. After obtaining the controller, you also need to set the PWM frequency. The software PWM controller's frequency range is between 40-1000Hz (low poor ......), A number that is not in this range throws an exception.
PwmController controller = (await PwmController.GetControllersAsync(Ligh
MCU simulation SPI interface-deep understanding of SPI bus protocol SPI (serial peripheral interfacer serial peripheral interface) is a synchronous serial communication interface launched by Motorola, the serial connection between the microprocessor compaction controller and the peripheral extended chip has developed into an industrial standard. Currently, variou
Through the first article, we already know that the whole SPI drive architecture can be divided into three parts: Protocol driver, common interface layer and controller driver. Among them, the controller driver is responsible for the lowest data receiving and dispatching work, in order to complete the data receiving and dispatching, the controller driver needs to complete the following functions:
1. Apply for the necessary hardware resources, such as
We know that SPI data transfer can be in two ways: synchronous and asynchronous. The so-called synchronization means that the initiator of the data transmission must wait for the end of this transmission, can not do other things, in code to explain that, after the transfer function is called, until the data transfer completes, the function will return. The asynchronous approach is the opposite, the initiator of the data transmission without waiting fo
SPI communication details, spi communicationSPI data transmission and receiving Mechanism1 SPI OverviewSPI is a ring bus structure that operates in the master-slave mode. This mode usually has one master device and one or more slave devices and requires at least four lines (during Unidirectional transmission, the three lines can also be used), which is composed o
We know that SPI data transfer can be in two ways: synchronous and asynchronous. The so-called synchronization means that the originator of the data transfer must wait for the end of the transmission, the period can not do other things, in code to explain that the function is called after the transfer, until the data transfer is complete, the function will return. And the asynchronous way is just the opposite, the initiator of data transmission does n
#include "iospiflash.h"/*******************************************//This was a IOSPI (Simulater by IO)//Lib for Driver Flash W25Q64BV//*******************************************/Sbit ioflashspi_cs= p1^0;Sbit Ioflashspi_din = p1^3;Sbit ioflashspi_dout = p1^4;Sbit ioflashspi_clk = p1^5;/*******************************************//IOSPI Base FUNCData shifting at the--rising edge--of the CLKCLK need a Hold Time Mydelay (3)//ShiftWrite U8Read U8//1Time Series requires:The w25q64b Flash support the
Linux Device Driver inquiry 1st days ---- spi Driver (1), 1st days ---- spi
This document allows reprinting. Please indicate the source:Http://blog.csdn.net/fulinus
The Linux kernel code is too big, and a small module will make you feel helpless. This afternoon, I am determined to take a good look at the spi driver.
First, analyze the spidev. c file, which define
Spring transaction SPI and configuration introduction, spring transaction spi
Abstract of Spring transaction management. Three core interfaces are PlatformTransactionManager, TransactionDefinition, and TransactionStatus. Shows the link:
TransactionDefinition:Defines Spring-compatible transaction attributes, including transaction isolation level, transaction Propagation Behavior, timeout duration, and read
Timers are commonly used by single-chip microcomputer. They are used to generate precise timing or other functions. MSP430 timers can not only complete precise timing, but also generate PWM waveform output, and capture time value (when the rising or falling edge arrives ). A general PWM waveform is generated here.Program.
Hardware introduction: The timera of MSP430 Series Single-Chip Microcomputer
1. TIMER output PWM basic ConceptPulse width modulation (PWM), an abbreviation for the English "pulse width modulation", is called pulse width modulation, which is a very effective technique for controlling analog circuits using the digital output of a microprocessor. The simple point is the control of the pulse width. Generally used to control the speed of stepper motor and so on.STM32 timers, in addition
The content source of this page is from Internet, which doesn't represent Alibaba Cloud's opinion;
products and services mentioned on that page don't have any relationship with Alibaba Cloud. If the
content of the page makes you feel confusing, please write us an email, we will handle the problem
within 5 days after receiving your email.
If you find any instances of plagiarism from the community, please send an email to:
info-contact@alibabacloud.com
and provide relevant evidence. A staff member will contact you within 5 working days.