The ping command is a very common tool used to diagnose network connectivity, the ping command uses the ICMP protocol, and the full spelling of ICMP is Internet Control message Protocol, the network controlled messaging protocol.In ICMP there are two parts for detecting network connectivity, one is the type, the other is code, and the Echo request and Echo reply,
10.3.0.0/16: fetches all data streams except for IP addresses starting with 10.3
IP proto
IP[2:2]==
Ip[8]==
Ip[9]==
ICMP[ICMPTYPE]==
The first number in square brackets represents the offset from the beginning of the protocol header, and the second number indicates how many bits need to be observed.crawl a stream of data sent to a broadcast or multicast address :By listening to broadcast or multicast traffic, you can master
net 10.13.32.169//listening for all IP packets on the local network
listening for ICMP packets
$ Tcpdump ' icmp[icmptype]!= Icmp-echo and Icmp[icmptype]!= icmp-echoreply '
//print except ' echo Request ' or ' echo ICMP packets
the process of ping Baidu, we use Wireshark grab the bag, so it is more intuitive. As shown, the ICMP protocol is a typical one-answer mode, the machine sends the ICMP request packet to the Baidu server, if the request packet arrives at the destination successfully, the Baidu server responds to the ICMP response packe
Wireshark data grasping Wireshark capturing data Wireshark grasping the packet methodWhen using Wireshark to capture Ethernet data, you can capture the analysis to your own packets, or you can capture the same LAN and capture the other person's packets in case you know the IP address of the other.Wireshark capturing it
. ExperimentIn this experiment, I want to use my own devices for the purpose of learning and want to further understand the network and Protocol applications. Therefore, the attack scope is relatively small, and the time is only a few seconds, does not affect any device. Let's talk about our attack steps: We use host 172.0.5.183 as our attack host, disguise ourselves as host 172.0.5.182, and launch ICMP flood attacks on host 172.0.5.9. At the beginnin
Install and run wireshark in linux, and run wireshark in linux
I. InstallationRun the command as root: yum install wiresharkIi. RunningEnter the command in the terminal:# WiresharkBash: wireshark: command not found# Whereis wiresharkWireshark:/usr/lib/wireshark/usr/share/wireshark
Software download for analysis: Wireshark-win32-1.10.2.exeRead the guided Tour1. Analyze and apply the ARP protocol2. Analyzing IP Protocols3. Analyzing the ICMP protocol1. Analysis of the format and content of ARP messages(1) The ARP request message of ping 172.18.3.132:000108000604000100e04c512ae8ac12038e000000000000ac120384Physical network Type hardware type:0001-ethernet (1)Protocol type Protocol TYPE:0
1. Copyright NoticeThis series of articles is I spent a lot of effort written, Wireshark is open source software, I am also willing to share technical knowledge and experience, is to appreciate and promote the spirit of open source, so anyone who see this article can be reproduced at will , but only a request:In the case of large paragraphs or even full-text references to this series of articles, it is necessary to retain My Network name (Zhaozi) and
Wireshark analyzes non-standard port traffic and wireshark PortWireshark analysis of non-standard port traffic 2.2.2 analysis of non-standard port traffic Wireshark analysis of non-standard port traffic
Non-standard port numbers are always the most common concern of network analysis experts. Check whether the application intends to use a non-standard port, or sec
One-stop learning Wireshark (i): Wireshark basic usagehttp://blog.jobbole.com/70907/In accordance with international practice, from the most basic of speaking.Crawl Messages :After downloading and installing the Wireshark, start Wireshark and select the interface name in the interface list and start grabbing the packet
abstract : In accordance with international practice, from the most basic of speaking. Crawl message: After downloading and installing the Wireshark, start Wireshark and select the interface name in the interface list and start grabbing the packet on this interface. For example, if you want to crawl traffic on a wireless network, click the wireless interface. Click Capture options to configure advanced prop
In accordance with international practice, from the most basic of speaking.Crawl Messages :After downloading and installing the Wireshark, start Wireshark and select the interface name in the interface list and start grabbing the packet on this interface. For example, if you want to crawl traffic on a wireless network, click the wireless interface. Click Capture options to configure advanced properties, but
Linux statistical analysis traffic-wireshark, statistical analysis-wireshark
Wireshark is an open-source packet capture tool with an interface. It can be used for statistical analysis of system traffic.Install
Wireshark has an interface, so it is generally run in the interface environment. You can install it through yu
Wireshark packet capture analysis-network protocol
Wireshark is currently the most popular packet capture tool. It can run in windows, Linux, and Mac OS X operating systems, and provides a friendly graphical interface. Wireshark also provides a powerful data packet capture function. It can capture the network data packets required by users in various ways. Howeve
How to Use wireshark to view ssl content and wireshark to view ssl
1. To view the ssl content, you need to obtain the server rsa key of the server.
2. Open wireshark and find the following path: Edit-> Preferences-> protocols-> SSL
Then click RSA Keys List: Edit,
Create a New RSA key on the New RSA editing interface
Where
IP address is the IP address of the serve
WireShark data packet analysis data encapsulation, wireshark data packetWireShark packet analysis data encapsulation
Data Encapsulation refers to the process of encapsulating a Protocol Data Unit (PDU) in a group of protocol headers and tails. In the OSI Layer-7 reference model, each layer is primarily responsible for communicating with the peer layer on other machines. This process is implemented in the Pr
I. Problem Description
Install ubuntu14.04 on the PC and log on as the root user.
When Wireshark is started, the following error dialog box appears:
Lua: error during loading: [String "/usr/share/Wireshark/init. Lua"]: 46: dofile has been disabled due to running Wireshark as superuser.
Ii. Solution
Modify/usr/share/W
The content source of this page is from Internet, which doesn't represent Alibaba Cloud's opinion;
products and services mentioned on that page don't have any relationship with Alibaba Cloud. If the
content of the page makes you feel confusing, please write us an email, we will handle the problem
within 5 days after receiving your email.
If you find any instances of plagiarism from the community, please send an email to:
info-contact@alibabacloud.com
and provide relevant evidence. A staff member will contact you within 5 working days.