spi multiplexer

Address: http://www.cnblogs.com/yanhc/archive/2008/08/22/2175269.html I recently participated in the adi udc (University Design Competition) competition to debug the touch screen. I used BF533. After debugging the SPI for half a day, I asked Yiqi, But I replied with a barrier, later I asked about the DSP technical support of Adi in China. They also debugged myCode, Really responsible, it turns out that I didn't add ssync (); this statement.Howeve

Toss for nearly one months of SPI communication (if it is big God's words estimated early to get out, but the harvest is quite large, at least almost understand the SPI subsystem), finally small results, cubieboard on the SPI mouth, is also called through, Here to thank Hipboi and so on the network of the Great God to help me, thanks to CCTV.First of all, related

The S3C2440 contains two serial peripheral device interfaces (SPI ports), each of which has two 8-shift register for sending and receiving, respectively, in one SPI communication, data is synchronously sent (in serial mode) and received (in serial mode ). The rate of 8-bit serial data is determined by the content of the relevant control register. If you only want to send data, some virtual data will be rece

1. IntroductionThe SPI full name is the service Provider Interface, the provider interface, the service usually refers to an interface or an abstract class, the service provider is a concrete implementation of this interface or abstract class, by the third party to implement the interface to provide specific services. SPI provides a dynamic mechanism for extending applications, often as an extension of the

The Serial Peripherals Interface (serial peripheral INTERFACE,SPI) is developed by Motorola to provide a low-cost, Easy-to-use interface between microcontrollers and peripheral chips (SPI is sometimes referred to as a 4-line interface). This interface can be used to connect memory, Ad/da converters, real-time clock calendars, LCD drives, sensors, audio chips, and even other processors. Currently, there are

The 4 operating modes of the SPI bus 0 to 4 Modesspi interface is the full name of "Serial peripheral Interface", meaning the serial peripheral interface, Motorola first defined on its MC68HCXX series processor. The SPI interface is used primarily in eeprom,flash, real-time clocks, ad converters, and digital signal processors and digital signal decoders.The SPI i

spi_device * u8 * }; N_SPI_MINORS 32 /* ... up to 256 */ DECLARE_BITMAP(minors, N_SPI_MINORS); DECLARE_BITMAP(name,bits) \ name[BITS_TO_LONGS(bits)] spidev_open( inode *inode, file * spidev_data * status = - mutex_lock( list_for_each_entry(spidev, (spidev->devt == inode-> status = (status == (!spidev-> spidev->buffer =

Serial communication: UART, SPI, i²c differential "reference"1, the UART is two lines, one sends a receive, can be full duplex communication, the number of lines is also relatively small. The data is transmitted asynchronously, the timing requirements of both sides are stricter, and the communication speed is not very fast. The most used on multi-machine communication.2, SPI interface and above the UART, mo

SPI Communication Protocol The SPI is a synchronous serial communication interface.SPI is the abbreviation of English serial Peripheral interface, as the name implies is the serial peripheral device interface. SPI is a high-speed, full-duplex, synchronous communication bus, the standard SPI also uses only 4 pins, comm

Overview SPI Flash, divided into SPI Flash, DUAL SPI Flash, QUAD SPI Flash, 3-wire SPI, 4-wire SPI, 6-wire SPI. In the case of clock, the more the number of lines in theory, the faster

SPI (service Providerinterface) is a powerful guarantee for Dubbo. Core support class Extensionloader.The concrete analysis can refer to the 1. More important annotations@SPI: Identity of the extension point interface: scope on class;@Adaptive: Provides parameters for generating Adaptive instances, scoped on classes or methods;@Activate: The load extension can be automatically activated by the framework, an

The SPI interface has four different data transmission timings, depending on the combination of the two bits of Cpol and CPHL. The four timings are shown in Figure 1,The relationship between time series and Cpol and CPHL can also be seen.Figure 1The Cpol is used to determine the level at which the SCK clock signal is idle, cpol=0, the idle level is low, cpol=1,The idle level is high. Cpha is used to determine the sampling time, cpha=0, the first clock

Introduction to SPI The SPI is all called (Service Provider Interface), a service discovery mechanism built into the JDK. A service usually refers to a known interface or abstract class, the service provider is the implementation of the interface or abstract class, and then stored in the resource path Meta-inf/services directory according to the SPI standard, th

1 introduction of SPI mechanism The full name of the SPI is the service Provider Interface. Most developers may be unfamiliar because this is for vendors or plug-ins. A more detailed description is available in the Java.util.ServiceLoader documentation. Simply summarize the idea of the Java SPI mechanism. The abstract modules in our system often have many differ

Design principles: A brief discussion of SPI and API background The first time I heard that SPI is reading "The Art of software framework Design," later in the Log4net and quartz.net found in this form of organizing code, the standard gives why to distinguish between SPI and API of a thinking process. speaking from interface-oriented programming We introduced t

It took more than half a month to figure out the SPI. In general, the road was not smooth, but the goal was finally achieved. Q24plus provides a three-line SPI (I/O/CLK/EN). Io can be automatically controlled by the bus into the input or output status, and enabled by the function. The clock is configured according to the configuration. , A maximum of 13 MHz and a minimum of 812.5 kHz. Supports

Serial peripheral interface (SPI ). Initialization steps:1. Connect to the SPI peripheral clock and set it through RCC-> apb2enr.2. Connect the peripheral clock of the reused gpio, which is also set through RCC-> apb2enrFor more information about how to connect the gpio clock, see section 8.1.4 of the stm32 reference manual.As mentioned in the manual: For the multiplexing output function, the port must be c

Whether in the network or communication field, as long as it is related to electronics or intelligence, you can find that they all have certain protocols. Now we will introduce the SPI bus protocol. The SPI bus protocol is a communication protocol. What is its concept? Now let's take a look at it from the article. SPI, short for Serial Peripheral Interface, is a

How to use the SPI Library1 Declare the SPI Hanlde, for example:SPI_HandleTypeDef hspi2 initializing the underlying resource by implementing the Hal_spi_mspinit () functionThe following two must be initializedA enable SPI clockb Configuring the SPI PinsThe following is initialized as neededC NVIC Interrupt Configuratio

ObjectiveOpenWrt's newest kernel (3.14.28) has been able to support both read-write and erase operations for 32M SPI Flash. However, the system may be poorly considered or a bug in the MT7620 system, on the W25Q256 Development Board system configured MT7620, Unable to soft reset! after consulting the relevant data, found that the MT7620 default support 24bit (3byte) SPI address mode, and to support more tha